CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] When[emc]

on 2000-06-25 13:53:10 UTC
Derik,

I'm with you there, I just wanted to copy a windoz95 drive on an old
machine to a bigger drive for CNC use in the garage. I still get
warnings of files not found for some hardware/driver that I can't figure
out. And yes, I even re-installed Windoz from the CD!

If I understood you, I wouldn't immediately burn those CD's! I'd check
to see it all that could be done. (Old DOS 6.22 didn't have that
problem!)

Good luck, and I'm sure we'll all be watchin' for your progress! Might
make LINUX (and EMC) users out of some of us after all!

Alan

"Derek B." wrote:
>
> I agree with you 100%!
> I have been talking with Tim Goldstein about burning Cd-roms. Tim seems
> to have worked out all the bugs and has a smooth running program. What I
> want to do is copy his complete setup off of his computer, with all the
> patches installed etc. and burn this to cd-rom.
>
> I am willing to burn the 50 cd-roms I have, for the list, for just the
> shipping cost of approximately $2.50 each. I might be wrong but all you
> would have to do is partition a drive and copy the cd-rom to the
> partition. It would be like making a duplicate of the original hard
> drive, which has the complete operating system. Possibly it might take 2
> cd-roms.
> Let me know if any one is interested, feedback is important.
> Derek B.
>
> wanliker@... wrote:
> >
> > My questions today are:
> >
> > 1. When is it going to get easy to implement LINUX/EMC, without being a
> > programmer to get it running? How about it programmers, make it as easy as
> > Windoz. Put disc in, and run in xx minutes.
> >
> > bill
> >
> > ------------------------------------------------------------------------
> > Was the salesman clueless? Productopia has the answers.
> > http://click.egroups.com/1/4633/4/_/423600/_/961788848/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
>
> ------------------------------------------------------------------------
> CLICK HERE AND START SAVING ON LONG DISTANCE BILLS TODAY!
> http://click.egroups.com/1/4125/4/_/423600/_/961867452/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager

Discussion Thread

Derek B. 2000-06-24 10:24:12 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Jon Anderson 2000-06-24 12:08:52 UTC Re: [CAD_CAM_EDM_DRO] When[emc] wanliker@a... 2000-06-24 12:09:25 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Steve Carlisle 2000-06-24 12:36:21 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Rich 2000-06-24 13:45:03 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Carey L. Culpepper 2000-06-24 13:47:58 UTC Re: [CAD_CAM_EDM_DRO] When[emc] petermic@p... 2000-06-24 15:37:46 UTC Re: When[emc] Derek B. 2000-06-24 15:38:49 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Jeff Rossel 2000-06-24 16:46:51 UTC Re: When[emc] James Cullins 2000-06-24 17:30:40 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Andrew Kozlowski 2000-06-25 05:47:38 UTC Re: [CAD_CAM_EDM_DRO] When[emc] james owens 2000-06-25 08:33:09 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Peter Smith 2000-06-25 09:47:26 UTC Re: [CAD_CAM_EDM_DRO] When[emc] johndroc@a... 2000-06-25 10:47:58 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Spehro Pefhany 2000-06-25 10:58:56 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Roland Friestad 2000-06-25 12:57:53 UTC Re: Re: When[emc] Alan Marconett KM6VV 2000-06-25 13:53:10 UTC Re: [CAD_CAM_EDM_DRO] When[emc] Wayde Gutman 2000-07-01 13:18:41 UTC Re: [CAD_CAM_EDM_DRO] When[emc]