Re: [CAD_CAM_EDM_DRO] Please help...3 phase Stepper motor translator
Posted by
jerry stout
on 2005-10-28 00:35:31 UTC
On 10/28/05, Andrey Lipavsky <alipavsky@...> wrote:
Novatronics
20A33H1-B
Made in Canada
Black wire common, Red #1, Brown #2 and Orange #3
Variable reluctance 3 phase stepper
19 ohms per phase
9 volts @ 0.47 Amp
12 volts @.63 Amp but gets very hot
15 degrees per step
I would also apreciate anny info or control circuits.
[Non-text portions of this message have been removed]
>Hey I have some of these motors too.
> WEDM has 4 wires, 1 common and 3 phases,
> therefore I need a translator circuit to translate
> Step & Dir from Parallel port to 3 phase pulse
> sequence..
>
> Please help me by provideing me the possible
> circuit/logic diagram for this..or any other
> suggestion???
>
> Regards
>
> Babar
Novatronics
20A33H1-B
Made in Canada
Black wire common, Red #1, Brown #2 and Orange #3
Variable reluctance 3 phase stepper
19 ohms per phase
9 volts @ 0.47 Amp
12 volts @.63 Amp but gets very hot
15 degrees per step
I would also apreciate anny info or control circuits.
[Non-text portions of this message have been removed]
Discussion Thread
Bill Vance
2005-10-27 10:33:06 UTC
Your mill could save your life
John Johnson
2005-10-27 11:00:00 UTC
Re: [CAD_CAM_EDM_DRO] Your mill could save your life
Pete Brown (YahooGroups)
2005-10-27 13:04:53 UTC
Urban Legends (was RE: [CAD_CAM_EDM_DRO] Your mill could save your life)
Steven Trovato
2005-10-27 13:28:59 UTC
Re: [CAD_CAM_EDM_DRO] Your mill could save your life
Babar
2005-10-27 21:23:07 UTC
[CAD_CAM_EDM_DRO] Please help...3 phase Stepper motor translator
Andrey Lipavsky
2005-10-27 23:05:09 UTC
RE: [CAD_CAM_EDM_DRO] Please help...3 phase Stepper motor translator
jerry stout
2005-10-28 00:35:31 UTC
Re: [CAD_CAM_EDM_DRO] Please help...3 phase Stepper motor translator
didier groenweghe
2005-10-28 19:04:19 UTC
Re: [CAD_CAM_EDM_DRO] Please help...3 phase Stepper motor translator
Paul Kelly
2005-10-28 21:57:27 UTC
ballscrew swarf protector
George Taylor, IV
2005-10-28 22:15:43 UTC
RE: [CAD_CAM_EDM_DRO] ballscrew swarf protector
JanRwl@A...
2005-10-28 22:17:52 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector
Paul Kelly
2005-10-28 22:20:24 UTC
RE: [CAD_CAM_EDM_DRO] ballscrew swarf protector
Blue
2005-10-29 00:42:43 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector
Paul Kelly
2005-10-29 00:52:21 UTC
RE: [CAD_CAM_EDM_DRO] ballscrew swarf protector
turbulatordude
2005-10-29 05:35:40 UTC
Re: ballscrew swarf protector
Steve Haushahn
2005-10-29 06:07:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: ballscrew swarf protector
Paul Kelly
2005-10-29 06:33:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: ballscrew swarf protector
Paul Kelly
2005-10-29 06:35:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: ballscrew swarf protector
Blue
2005-10-29 07:06:01 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector
Steve Blackmore
2005-10-29 07:21:14 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector
bulshatar
2005-10-29 09:33:09 UTC
Re: ballscrew swarf protector
Jon Elson
2005-10-29 12:52:16 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector
Hugh Prescott
2005-10-29 17:46:34 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector
Jon Elson
2005-10-29 19:00:53 UTC
Re: [CAD_CAM_EDM_DRO] ballscrew swarf protector