RE: [CAD_CAM_EDM_DRO] Re: Manual Control
Posted by
Alan Marconett
on 2005-12-19 12:28:06 UTC
Hi Glen, List,
Could probably be done in a PIC or similar uP.
Alan KM6VV
Could probably be done in a PIC or similar uP.
Alan KM6VV
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of vrsculptor
> Sent: Monday, December 19, 2005 8:31 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: Manual Control
>
> Glen,
> USDigital has an encoder to step/direction chip. See:
> http://www.usdigital.com/products/ls7183-ls7184
>
> The 84 is the one you are looking for.
>
> Roger
>
Discussion Thread
roboticscnc
2005-04-13 07:25:12 UTC
Manual Control
Mike
2005-04-13 08:11:26 UTC
Re: Manual Control
roboticscnc
2005-12-16 04:50:36 UTC
Manual Control
roboticscnc
2005-12-18 00:37:12 UTC
Manual Control
alphawolf45
2005-12-18 05:25:58 UTC
Re: Manual Control
R Rogers
2005-12-18 07:06:24 UTC
Re: [CAD_CAM_EDM_DRO] Manual Control
James Peck
2005-12-19 05:04:20 UTC
RE: [CAD_CAM_EDM_DRO] Manual Control
roboticscnc
2005-12-19 07:05:29 UTC
Re: Manual Control
Stephen Wille Padnos
2005-12-19 07:22:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
Derek Brodeur
2005-12-19 07:22:32 UTC
Re: Manual Control
roboticscnc
2005-12-19 07:41:44 UTC
Re: Manual Control
vrsculptor
2005-12-19 08:32:08 UTC
Re: Manual Control
Derek Brodeur
2005-12-19 08:42:03 UTC
Re: Manual Control
Alan Marconett
2005-12-19 12:28:06 UTC
RE: [CAD_CAM_EDM_DRO] Re: Manual Control
vrsculptor
2005-12-19 16:09:45 UTC
Re: Manual Control
roboticscnc
2005-12-27 00:17:13 UTC
Re: Manual Control
Les Newell
2005-12-27 00:35:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
roboticscnc
2005-12-27 00:50:13 UTC
Re: Manual Control
Steve Haushahn
2005-12-27 04:39:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
Dan Mauch
2005-12-27 08:31:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
Les Newell
2005-12-28 05:13:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
roboticscnc
2005-12-28 06:56:35 UTC
Re: Manual Control
Les Newell
2005-12-28 07:26:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control