Re: Manual Control
Posted by
roboticscnc
on 2005-12-28 06:56:35 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Les Newell <lesnewell@h...> wrote:
condition the disconnected step wire picks up the occasional pulse
from the other axis' encoder and slowly moves the servo. This doesn't
happen when the step wire is reconnected, as it is tied either high or
low.
I'm using a deskcnc driver and a tek10 driver. The deskcnc one works
perfectly but the tek10 may have different requirements for the
step/direction inputs.It may be trying to oscillate backwards &
forwards with the quadrature inputs. Apart from this the tek10 works
perfectly when controlled from the computer. ( as it was designed to ).
>Yes, the motor stops if the step wire is disconnected, however in this
> That is odd. If you disconnect the step input does the motor stop? Do
> the drives have step multipliers?
>
> Les
>
> >The servo encoders are still connected to the drivers and the manually
> >controled encoders are connected to the step / direction inputs. I'ts
> >as if the servo drivers see a continuous signal as full speed pulses.
> >
> >
> >
> >
>
condition the disconnected step wire picks up the occasional pulse
from the other axis' encoder and slowly moves the servo. This doesn't
happen when the step wire is reconnected, as it is tied either high or
low.
I'm using a deskcnc driver and a tek10 driver. The deskcnc one works
perfectly but the tek10 may have different requirements for the
step/direction inputs.It may be trying to oscillate backwards &
forwards with the quadrature inputs. Apart from this the tek10 works
perfectly when controlled from the computer. ( as it was designed to ).
Discussion Thread
roboticscnc
2005-04-13 07:25:12 UTC
Manual Control
Mike
2005-04-13 08:11:26 UTC
Re: Manual Control
roboticscnc
2005-12-16 04:50:36 UTC
Manual Control
roboticscnc
2005-12-18 00:37:12 UTC
Manual Control
alphawolf45
2005-12-18 05:25:58 UTC
Re: Manual Control
R Rogers
2005-12-18 07:06:24 UTC
Re: [CAD_CAM_EDM_DRO] Manual Control
James Peck
2005-12-19 05:04:20 UTC
RE: [CAD_CAM_EDM_DRO] Manual Control
roboticscnc
2005-12-19 07:05:29 UTC
Re: Manual Control
Stephen Wille Padnos
2005-12-19 07:22:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
Derek Brodeur
2005-12-19 07:22:32 UTC
Re: Manual Control
roboticscnc
2005-12-19 07:41:44 UTC
Re: Manual Control
vrsculptor
2005-12-19 08:32:08 UTC
Re: Manual Control
Derek Brodeur
2005-12-19 08:42:03 UTC
Re: Manual Control
Alan Marconett
2005-12-19 12:28:06 UTC
RE: [CAD_CAM_EDM_DRO] Re: Manual Control
vrsculptor
2005-12-19 16:09:45 UTC
Re: Manual Control
roboticscnc
2005-12-27 00:17:13 UTC
Re: Manual Control
Les Newell
2005-12-27 00:35:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
roboticscnc
2005-12-27 00:50:13 UTC
Re: Manual Control
Steve Haushahn
2005-12-27 04:39:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
Dan Mauch
2005-12-27 08:31:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
Les Newell
2005-12-28 05:13:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control
roboticscnc
2005-12-28 06:56:35 UTC
Re: Manual Control
Les Newell
2005-12-28 07:26:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Manual Control