RE: [CAD_CAM_EDM_DRO] emc problems

We've never had board or motors connected to this thing (yet); just
running EMC in simulation on the PC. What do you mean by 'periphery'?
What settings should I check I safe mode?
I skimmed the FAQ over at the EMC site with not much luck. Checked a
couple other trouble-shooting files over there as well with equal
results.
My 'expert' is 350km away right now and cannot get here to help. On
our own, more or less.
Thanks,

Keith



-----Original Message-----
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Familia Peter Arce
& TAD
Sent: December 31, 2005 8:37 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] emc problems


Linux that works is great, Linux that goes on strike #""&$$#(UT G¡==)>X*
Since May I am not able to throw windows away, because neither me nor my
professor from tecnical high school were able to get it running. It
sounds like you need to set up right the perifery. And if your EMC set
up allready and you took off the interface cards and drivers, then the
machine expects them and cannot find them. First thing run safe mode and
check the settings. Later get a specialist. That is why the "free"
software may sometimes become more expensive then the payed licence
software.


----- Mensaje Original -----
De: Ray Webster <tazman03@...>
Fecha: Sábado, Diciembre 31, 2005 0:43 am
Asunto: [CAD_CAM_EDM_DRO] emc problems

> Having what seems to be a driver issue here. My buddy installed
> a
> version of Linux on this machine I'm going to use with a homebrew
> gantry mill. Every time I start EMC, the computer locks up hard
> after
> a couple minutes. The Linux version screen says it's KDE ver.
> 3.3.2,
> Linux realease 2.6.12.6-magma. There are a couple versions of EMC
> on
> here (a Sherline version and the generic install) but either of
> them
> will lock up. Have to power down at the supply to break it.
> Any ideas anyone? I have switched monitor, keyboard and mouse
> to no
> effect. Installer said it ran ok on his bench, doesn't on mine.
> It's
> not hooked up to the mill yet.
> Thanks,
> Keith
>
>
>
>

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill
List Mom List Owner


Yahoo! Groups Links









__________ NOD32 1.1345 (20051230) Information __________

This message was checked by NOD32 antivirus system. http://www.eset.com