Re: MAGIC SMOKE Xylotex drives
Posted by
turbulatordude
on 2006-01-07 08:05:17 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@a... wrote:
performance ?
Here is a quote from the Gecko White Paper.
"Also note from the previous graph that motor output power doubles
when the power supply voltage is doubled for either series or
parallel-wired motors. Notice that a parallel-connected motor delivers
performance identical to a series-connected motor running at twice the
power supply voltage."
Dave
>when I
>
> I guess I was not clear, it is the Xylotex drives that are blowing
> either turn the power on or off, from what I can guess.solid.
> The switching power supply is rated at 24 volts/10 amps, and is rock
> My question that apparently threw everyone off, is should I add acouple of
> caps on the output, I will do this, at least enough to stop anyswitching
> spikes when it is switched on.finally
> The lathe was running well when I put it away for the remodeling,
> got some time and dug it out, and promptly lost two drives. Thesteppers are 8
> wire, hooked up in a parallel coil configuration. I plan to changethat to
> series to bring the current required down also. I should be withinthe
> Xylotex ratings, as it is wired.What effect does the lower voltage (per motor needs) have on the motor
> Thanks all for your comments.
> thanks,
> bill
performance ?
Here is a quote from the Gecko White Paper.
"Also note from the previous graph that motor output power doubles
when the power supply voltage is doubled for either series or
parallel-wired motors. Notice that a parallel-connected motor delivers
performance identical to a series-connected motor running at twice the
power supply voltage."
Dave
Discussion Thread
wanliker@a...
2006-01-06 19:20:39 UTC
MAGIC SMOKE Xylotex drives
R Rogers
2006-01-06 20:55:17 UTC
Re: [CAD_CAM_EDM_DRO] MAGIC SMOKE Xylotex drives
wanliker@a...
2006-01-06 21:01:17 UTC
Re: [CAD_CAM_EDM_DRO] MAGIC SMOKE Xylotex drives
caudlet
2006-01-06 23:04:46 UTC
Re: MAGIC SMOKE Xylotex drives
turbulatordude
2006-01-07 08:05:17 UTC
Re: MAGIC SMOKE Xylotex drives
Jymmm
2006-01-07 09:09:40 UTC
Re: MAGIC SMOKE Xylotex drives
John Johnson
2006-01-07 11:02:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
Vlad Krupin
2006-01-07 12:20:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
Andy Wander
2006-01-07 12:37:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
wanliker@a...
2006-01-07 17:06:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
wanliker@a...
2006-01-07 17:07:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
John Johnson
2006-01-08 07:26:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
John Johnson
2006-01-08 07:29:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
Darren Lucke
2006-01-08 10:18:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives
turbulatordude
2006-01-08 10:40:24 UTC
Re: MAGIC SMOKE Xylotex drives AVGAS is OFF TOPIC
turbulatordude
2006-01-08 11:07:00 UTC
Re: MAGIC SMOKE Xylotex drives - wire breakage
Jon Elson
2006-01-08 15:47:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives - wire breakage