CAD CAM EDM DRO - Yahoo Group Archive

Re: MAGIC SMOKE Xylotex drives

Posted by Jymmm
on 2006-01-07 09:09:40 UTC
Hi Bill,

You keep saying "blowing", as if they're resetting themselves.

I (somehow) did blow one driver on a 3 axis Xyltex board, and when I took a
meter to the outputs (power removed of course) of that driver - dead short.

The Xylotex board has a surface mount LED, it will come on for a moment, then
shut off upon power up when one of more drivers are blown/shorted.

Are you seeing any of these symptoms?

Have you contact Jeff of Xylotex? He's really helpful in these situations.

Jim...

> Date: Fri, 6 Jan 2006 22:20:27 EST
> From: wanliker@...
> Subject: MAGIC SMOKE Xylotex drives
>
>
> I guess I was not clear, it is the Xylotex drives that are blowing when I
> either turn the power on or off, from what I can guess.
> The switching power supply is rated at 24 volts/10 amps, and is rock
> solid.
> My question that apparently threw everyone off, is should I add a couple of
>
> caps on the output, I will do this, at least enough to stop any switching
> spikes when it is switched on.
> The lathe was running well when I put it away for the remodeling, finally
> got some time and dug it out, and promptly lost two drives. The steppers
> are 8
> wire, hooked up in a parallel coil configuration. I plan to change that
> to
> series to bring the current required down also. I should be within the
> Xylotex ratings, as it is wired.
> Thanks all for your comments.
> thanks,
> bill




__________________________________________
Yahoo! DSL – Something to write home about.
Just $16.99/mo. or less.
dsl.yahoo.com

Discussion Thread

wanliker@a... 2006-01-06 19:20:39 UTC MAGIC SMOKE Xylotex drives R Rogers 2006-01-06 20:55:17 UTC Re: [CAD_CAM_EDM_DRO] MAGIC SMOKE Xylotex drives wanliker@a... 2006-01-06 21:01:17 UTC Re: [CAD_CAM_EDM_DRO] MAGIC SMOKE Xylotex drives caudlet 2006-01-06 23:04:46 UTC Re: MAGIC SMOKE Xylotex drives turbulatordude 2006-01-07 08:05:17 UTC Re: MAGIC SMOKE Xylotex drives Jymmm 2006-01-07 09:09:40 UTC Re: MAGIC SMOKE Xylotex drives John Johnson 2006-01-07 11:02:26 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives Vlad Krupin 2006-01-07 12:20:18 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives Andy Wander 2006-01-07 12:37:27 UTC RE: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives wanliker@a... 2006-01-07 17:06:38 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives wanliker@a... 2006-01-07 17:07:28 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives John Johnson 2006-01-08 07:26:13 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives John Johnson 2006-01-08 07:29:03 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives Darren Lucke 2006-01-08 10:18:54 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives turbulatordude 2006-01-08 10:40:24 UTC Re: MAGIC SMOKE Xylotex drives AVGAS is OFF TOPIC turbulatordude 2006-01-08 11:07:00 UTC Re: MAGIC SMOKE Xylotex drives - wire breakage Jon Elson 2006-01-08 15:47:04 UTC Re: [CAD_CAM_EDM_DRO] Re: MAGIC SMOKE Xylotex drives - wire breakage