RE: [CAD_CAM_EDM_DRO] Re: Power draw bar
Posted by
Mark Vaughan
on 2006-12-29 02:38:17 UTC
Thanks Larry, I hoped that would be the case
Regs Mark
_____
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Larry Van Duyn
Sent: 29 December 2006 02:09
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: Power draw bar
I just finished one of power drawbars using the 3/8 butterfly air impact.
It is installed on my manual mill with no brake applied. There is enough
inertia in the spindle and motor assembly that the spindle does not even
turn when removing or inserting a tool. By the way it sure is handy.
No more
reaching to the top of the mill to twist that wrench. Should have done this
a long time ago...
Larry..
[Non-text portions of this message have been removed]
Regs Mark
_____
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Larry Van Duyn
Sent: 29 December 2006 02:09
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: Power draw bar
I just finished one of power drawbars using the 3/8 butterfly air impact.
It is installed on my manual mill with no brake applied. There is enough
inertia in the spindle and motor assembly that the spindle does not even
turn when removing or inserting a tool. By the way it sure is handy.
No more
reaching to the top of the mill to twist that wrench. Should have done this
a long time ago...
Larry..
[Non-text portions of this message have been removed]
Discussion Thread
Vince Endter
2006-12-20 15:02:33 UTC
Power draw bar
Mark Vaughan
2006-12-20 15:20:33 UTC
RE: [CAD_CAM_EDM_DRO] Power draw bar
BRIAN FOLEY
2006-12-20 15:34:05 UTC
Re: [CAD_CAM_EDM_DRO] Power draw bar
Ron Ginger
2006-12-21 09:32:12 UTC
Re: Power draw bar
HTCLKI@A...
2006-12-28 11:58:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power draw bar
Mark Vaughan
2006-12-28 17:50:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power draw bar
Larry Van Duyn
2006-12-28 18:15:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power draw bar
George Taylor, IV
2006-12-28 20:31:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power draw bar
Mark Vaughan
2006-12-29 02:38:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power draw bar
Polaraligned
2006-12-29 04:50:12 UTC
Re: Power draw bar
Vince Endter
2007-01-03 18:51:37 UTC
Power draw bar
BRIAN FOLEY
2007-01-03 20:01:45 UTC
Re: [CAD_CAM_EDM_DRO] Power draw bar
George Taylor, IV
2007-01-03 22:06:26 UTC
RE: [CAD_CAM_EDM_DRO] Power draw bar
Vince Endter
2007-01-04 06:17:19 UTC
Re: Power draw bar
George Taylor, IV
2007-01-04 20:30:34 UTC
RE: [CAD_CAM_EDM_DRO] Re: Power draw bar
kiwiavi
2007-01-06 02:09:43 UTC
Re: Power draw bar