Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Posted by
Steve Blackmore
on 2007-05-27 17:56:14 UTC
On Sun, 27 May 2007 22:27:45 +0100, you wrote:
not hard to remove the dross out of your replies, a couple of keystrokes
and we don't have to download the same stuff all over again!
Embarrassingly, my reply is a two liner..
Why don't you and Jon get together, bite the bullet and use his hardware
and EMC2? Or spend £7500 and have a solution tomorrow?
Steve Blackmore
--
>Yes I agree.124 lines of unnecessary quoting removed for a three word post!!!! It's
not hard to remove the dross out of your replies, a couple of keystrokes
and we don't have to download the same stuff all over again!
Embarrassingly, my reply is a two liner..
Why don't you and Jon get together, bite the bullet and use his hardware
and EMC2? Or spend £7500 and have a solution tomorrow?
Steve Blackmore
--
Discussion Thread
Zafar Salam
2007-05-26 08:18:08 UTC
Big servo motors drive recommendations
Mark Vaughan
2007-05-26 11:14:20 UTC
RE: [CAD_CAM_EDM_DRO] Big servo motors drive recommendations
vrsculptor
2007-05-26 13:26:48 UTC
Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-26 16:33:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Patrick J
2007-05-26 20:06:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Zafar Salam
2007-05-26 23:31:10 UTC
Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 01:48:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 02:04:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Steve Blackmore
2007-05-27 03:19:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Patrick J
2007-05-27 04:29:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 08:33:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Steve Blackmore
2007-05-27 08:35:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 08:37:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 08:42:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
thecalfees
2007-05-27 09:39:31 UTC
Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 11:01:28 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Jon Elson
2007-05-27 11:49:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Jon Elson
2007-05-27 11:55:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Jon Elson
2007-05-27 12:03:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 12:36:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 12:37:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
David G. LeVine
2007-05-27 13:42:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
David G. LeVine
2007-05-27 13:44:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Jon Elson
2007-05-27 14:22:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-27 14:49:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Steve Blackmore
2007-05-27 17:56:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-28 01:18:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Steve Blackmore
2007-05-28 02:49:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
John Stevenson
2007-05-28 04:27:24 UTC
Re: Big servo motors drive recommendations
John Stevenson
2007-05-28 04:35:34 UTC
Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-28 07:10:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Jon Elson
2007-05-28 21:33:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-29 00:11:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: Big servo motors drive recommendations
Mark Vaughan
2007-05-29 00:14:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC / Linux
Anders Wallin
2007-05-29 03:07:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC / Linux
Jon Elson
2007-05-29 11:18:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC / Linux
Polaraligned
2007-07-06 10:02:10 UTC
Big servo motors drive recommendations
Mark Vaughan
2007-07-06 12:00:33 UTC
RE: [CAD_CAM_EDM_DRO] Big servo motors drive recommendations
Polaraligned
2007-07-06 18:49:32 UTC
servo motors drives (Or Steppers?)
Mark Vaughan
2007-07-07 00:49:58 UTC
RE: [CAD_CAM_EDM_DRO] servo motors drives (Or Steppers?)