Re: Newbie Question
Posted by
Graham Stabler
on 2007-08-02 11:13:44 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Jack Mc Kie"
<freshwatermodels@...> wrote:
step and direction signals come from a PC (using mach3 software for
example) directly or from another controller of some sort.
The DeskCNC system takes serial messages from the PC and converts them
to step and direction signals, these can then be sent to stepper
drivers such as the Xylotex board.
You may well be able to buy the deskCNC controller complete with
stepper drivers in a box but this is an extension of the basic deskCNC
controller.
Graham
<freshwatermodels@...> wrote:
>The xylotex takes step and direction and then drives the motors, the
> Ron,
>
> The way I read it, and reread it, it needs only power supplies 12VDC,
> and 5VDC, wires, and steppers??? What am I missing?
step and direction signals come from a PC (using mach3 software for
example) directly or from another controller of some sort.
The DeskCNC system takes serial messages from the PC and converts them
to step and direction signals, these can then be sent to stepper
drivers such as the Xylotex board.
You may well be able to buy the deskCNC controller complete with
stepper drivers in a box but this is an extension of the basic deskCNC
controller.
Graham
Discussion Thread
Steve Greenfield
2000-11-29 09:00:38 UTC
Re: Newbie Question
Wally K
2000-11-29 09:28:25 UTC
Saving links
san3@s...
2001-07-13 01:37:31 UTC
Newbie Question
cncdxf@a...
2001-07-13 06:22:41 UTC
Re: Newbie Question
Tim Goldstein
2001-07-13 07:09:53 UTC
RE: [CAD_CAM_EDM_DRO] Newbie Question
kimvellore
2002-08-21 12:52:13 UTC
Newbie Question
Tom Benedict
2002-08-21 13:11:10 UTC
Re: [CAD_CAM_EDM_DRO] Newbie Question
j.guenther
2002-08-21 13:11:10 UTC
RE: [CAD_CAM_EDM_DRO] Newbie Question
teleteq
2005-05-11 14:33:32 UTC
Newbie Question
Codesuidae
2005-05-11 15:30:17 UTC
Re: [CAD_CAM_EDM_DRO] Newbie Question
turbulatordude
2005-05-11 15:58:55 UTC
Re: Newbie Question
Dave Shiels
2005-05-11 16:21:21 UTC
Re: [CAD_CAM_EDM_DRO] Newbie Question
teleteq
2005-05-11 16:43:53 UTC
Re: Newbie Question
Jack Mc Kie
2007-08-01 14:56:18 UTC
Newbie Question
Ron Ginger
2007-08-02 06:35:33 UTC
Re: Newbie Question
turbulatordude
2007-08-02 07:25:07 UTC
Re: Newbie Question - mini-mill conversion
Jack Coats
2007-08-02 07:53:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie Question
Jack Mc Kie
2007-08-02 10:00:12 UTC
Re: Newbie Question
Graham Stabler
2007-08-02 11:13:44 UTC
Re: Newbie Question
Jack Mc Kie
2007-08-02 11:40:11 UTC
Re: Newbie Question