noob laser question
Posted by
Cristi
on 2008-01-18 03:52:35 UTC
Hello,
I need to balance a tiny gyroscope disk ( about 50 mm diameter ) and I
would need a laser for this. The disc has a sharp edge at the exterior
( so I won't need lasers to cut very thick steel sheets ). My problem
- where I can buy such a laser and what would be a good choice for this?
I need to balance a tiny gyroscope disk ( about 50 mm diameter ) and I
would need a laser for this. The disc has a sharp edge at the exterior
( so I won't need lasers to cut very thick steel sheets ). My problem
- where I can buy such a laser and what would be a good choice for this?
Discussion Thread
Cristi
2008-01-18 03:52:35 UTC
noob laser question
R Wink
2008-01-18 04:35:29 UTC
RE: [CAD_CAM_EDM_DRO] noob laser question
NEVILLE WEBSTER
2008-01-18 10:17:39 UTC
RE: [CAD_CAM_EDM_DRO] noob laser question
R Wink
2008-01-18 15:06:37 UTC
RE: [CAD_CAM_EDM_DRO] noob laser question
Brandon LaCava
2008-01-18 15:06:58 UTC
Re: [CAD_CAM_EDM_DRO] noob laser question
Bob Muse
2008-01-18 17:09:07 UTC
Re: [CAD_CAM_EDM_DRO] noob laser question
Graham Stabler
2008-01-18 17:41:12 UTC
Re: noob laser question
Graham Stabler
2008-01-18 17:43:10 UTC
Re: noob laser question
Cristi
2008-01-19 01:54:14 UTC
Re: noob laser question
Cristi
2008-01-19 02:14:53 UTC
Re: noob laser question
hannu
2008-01-19 03:06:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Cristi
2008-01-19 03:18:00 UTC
Re: noob laser question
Peter Reilley
2008-01-19 05:29:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
optics22000
2008-01-19 08:56:43 UTC
Re: noob laser question
carbonsteelsam
2008-01-19 09:49:23 UTC
Re: noob laser question
Jon Elson
2008-01-19 10:46:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Jon Elson
2008-01-19 10:52:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Jon Elson
2008-01-19 10:56:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Jon Elson
2008-01-19 11:11:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Cristi
2008-01-19 14:00:10 UTC
Re: noob laser question
Steve Blackmore
2008-01-19 14:20:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Jon Elson
2008-01-19 21:39:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Dave Halliday
2008-01-19 21:51:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: noob laser question
Dave Halliday
2008-01-19 22:00:58 UTC
RE: [CAD_CAM_EDM_DRO] Re: noob laser question
Cristi
2008-01-19 23:15:55 UTC
Re: noob laser question
David LeVine
2008-01-20 12:21:50 UTC
Re: [CAD_CAM_EDM_DRO] Disc balance
Jon Elson
2008-01-20 12:34:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Steve Blackmore
2008-01-20 17:22:13 UTC
Re: [CAD_CAM_EDM_DRO] Disc balance
g_smith47
2008-01-20 20:42:45 UTC
Re: noob laser question
Joe Macmurchie
2008-01-20 20:44:01 UTC
RE: [CAD_CAM_EDM_DRO] Disc balance
Steve Blackmore
2008-01-21 00:16:42 UTC
Re: [CAD_CAM_EDM_DRO] Disc balance
Cristi
2008-01-21 00:33:52 UTC
Re: noob laser question
Paul Kelly
2008-01-21 04:04:08 UTC
RE: [CAD_CAM_EDM_DRO] Disc balance
Jon Elson
2008-01-21 11:22:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question
Cristi
2008-01-21 11:40:11 UTC
Re: noob laser question
Jon Elson
2008-01-21 20:12:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: noob laser question