Re: Torch Table
Posted by
Roland Jollivet
on 2009-04-30 15:50:18 UTC
Don't make your slats flat. This increases the chance of welding the work to
the slats when cutting. Most of the slats i've seen on laser tables are
sawtooth shaped. Here's a pic of some copper slats to get an idea;
http://www.fedtech.com/images/Copper_Slats_-_PR.jpg
Or maybe make them saw tooth on one side, and flat on the other, reversable.
Regards
Roland
2009/4/29 roboticscnc <gsm42@...>
the slats when cutting. Most of the slats i've seen on laser tables are
sawtooth shaped. Here's a pic of some copper slats to get an idea;
http://www.fedtech.com/images/Copper_Slats_-_PR.jpg
Or maybe make them saw tooth on one side, and flat on the other, reversable.
Regards
Roland
2009/4/29 roboticscnc <gsm42@...>
>[Non-text portions of this message have been removed]
>
> How are you supporting the slats ? My first plasma table was similar to
> this and the slats could wobble a bit, being only supported at each end
> (They were made of 75 x 3mm flat bar). If the metal being cut was
> bumped, or the torch touched it, all accuracy was lost. It would help to
> put another support through the middle at 90 degrees if this happens.
> I used a Thermal Dynamics Cutmaster 101 and it worked well - cheaper
> than Hypertherm. Use a Pilot Arc Plasma Cutter - which ever brand you
> choose. ( Less electrical noise )
> Regards,
> Glen.
> --- In CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO%40yahoogroups.com>,
> "jeremymaso" <jeremymaso@...>
> wrote:
>
> >
> > Hi, we're working on a torch table design and are looking for some
> feedback on it. We have some pictures of the latest design on the top
> right side of the project page, and the bill of materials is near the
> bottom: http://openfarmtech.org/index.php?title=Torch_table
> >
> > We still need to source a torch for it, any recommendations?
> >
> > Thanks for any feedback!
> >
>
>
>
Discussion Thread
jeremymaso
2009-04-27 16:50:58 UTC
Torch Table
xdonna
2009-04-27 17:23:47 UTC
Re: Torch Table
JCullins
2009-04-27 18:44:12 UTC
RE: Torch Table
Taslim Hyatali
2009-04-27 18:44:22 UTC
Re: Torch Table
roboticscnc
2009-04-29 06:50:53 UTC
Re: Torch Table
jeremymaso
2009-04-29 12:43:39 UTC
Re: Torch Table
jeremymaso
2009-04-29 12:43:54 UTC
Re: Torch Table
xdonna
2009-04-29 17:09:19 UTC
Re: Torch Table
Denis Casserly
2009-04-30 07:47:37 UTC
Re: Torch Table
Bob Campbell
2009-04-30 08:01:43 UTC
RE: Torch Table
Roland Jollivet
2009-04-30 15:50:18 UTC
Re: Torch Table
JCullins
2009-04-30 15:51:35 UTC
Re: Torch Table
xdonna
2009-04-30 17:47:34 UTC
Re: Torch Table
William Thomas
2009-05-01 18:01:49 UTC
W.E.T.Re: Torch Table
jeremymaso
2009-05-03 07:04:16 UTC
Re: Torch Table
turbulatordude
2009-05-03 07:30:44 UTC
Re: Torch Table
Tony Smith
2009-05-03 09:31:58 UTC
RE: Torch Table