CAD CAM EDM DRO - Yahoo Group Archive

Re: Torch Table

Posted by jeremymaso
on 2009-05-03 07:04:16 UTC
Good idea on the sawtooth slats! I think just some simple slat holders across the bottom of our table with cuts in them should work to keep the slats from moving around.

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Roland Jollivet <Roland.Jollivet@...> wrote:
>
> Don't make your slats flat. This increases the chance of welding the work to
> the slats when cutting. Most of the slats i've seen on laser tables are
> sawtooth shaped. Here's a pic of some copper slats to get an idea;
>
> http://www.fedtech.com/images/Copper_Slats_-_PR.jpg
>
> Or maybe make them saw tooth on one side, and flat on the other, reversable.
>
> Regards
> Roland
>
>
>
> 2009/4/29 roboticscnc <gsm42@...>
>
> >
> >
> > How are you supporting the slats ? My first plasma table was similar to
> > this and the slats could wobble a bit, being only supported at each end
> > (They were made of 75 x 3mm flat bar). If the metal being cut was
> > bumped, or the torch touched it, all accuracy was lost. It would help to
> > put another support through the middle at 90 degrees if this happens.
> > I used a Thermal Dynamics Cutmaster 101 and it worked well - cheaper
> > than Hypertherm. Use a Pilot Arc Plasma Cutter - which ever brand you
> > choose. ( Less electrical noise )
> > Regards,
> > Glen.
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO%40yahoogroups.com>,
> > "jeremymaso" <jeremymaso@>
> > wrote:
> >
> > >
> > > Hi, we're working on a torch table design and are looking for some
> > feedback on it. We have some pictures of the latest design on the top
> > right side of the project page, and the bill of materials is near the
> > bottom: http://openfarmtech.org/index.php?title=Torch_table
> > >
> > > We still need to source a torch for it, any recommendations?
> > >
> > > Thanks for any feedback!
> > >
> >
> >
> >
>
>
> [Non-text portions of this message have been removed]
>

Discussion Thread

jeremymaso 2009-04-27 16:50:58 UTC Torch Table xdonna 2009-04-27 17:23:47 UTC Re: Torch Table JCullins 2009-04-27 18:44:12 UTC RE: Torch Table Taslim Hyatali 2009-04-27 18:44:22 UTC Re: Torch Table roboticscnc 2009-04-29 06:50:53 UTC Re: Torch Table jeremymaso 2009-04-29 12:43:39 UTC Re: Torch Table jeremymaso 2009-04-29 12:43:54 UTC Re: Torch Table xdonna 2009-04-29 17:09:19 UTC Re: Torch Table Denis Casserly 2009-04-30 07:47:37 UTC Re: Torch Table Bob Campbell 2009-04-30 08:01:43 UTC RE: Torch Table Roland Jollivet 2009-04-30 15:50:18 UTC Re: Torch Table JCullins 2009-04-30 15:51:35 UTC Re: Torch Table xdonna 2009-04-30 17:47:34 UTC Re: Torch Table William Thomas 2009-05-01 18:01:49 UTC W.E.T.Re: Torch Table jeremymaso 2009-05-03 07:04:16 UTC Re: Torch Table turbulatordude 2009-05-03 07:30:44 UTC Re: Torch Table Tony Smith 2009-05-03 09:31:58 UTC RE: Torch Table