RE: [CAD_CAM_EDM_DRO] Re: reprap build started
Posted by
Alan
on 2011-10-12 13:38:16 UTC
I was surprised to see the extruder also be a replicated part. Aluminum
would seem to be desired here. But they are getting away with it! (I
really like aluminum).
After watching the videos of the SAE Prusa Mendel being assembled, I'm
convinced that rigidity is not an issue. Always good to look at new ways to
build things. In a similar vein, wood and plastic routers are being built
with "alternate" construction methods. Plumbing pipe!
I'll keep following their progress.
Alan KM6VV
would seem to be desired here. But they are getting away with it! (I
really like aluminum).
After watching the videos of the SAE Prusa Mendel being assembled, I'm
convinced that rigidity is not an issue. Always good to look at new ways to
build things. In a similar vein, wood and plastic routers are being built
with "alternate" construction methods. Plumbing pipe!
I'll keep following their progress.
Alan KM6VV
> -----Original Message-----
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Mike Payson
>
> Trust me, there is NO reason to mill the parts other than convenience.
> Assuming they are printed well, the printed parts are PLENTY strong.
> Remember, the loads on a 3d printer are trivial compared to the loads
> on a router. That is why these "flimsy" little threaded rod
> contraptions are reliably able to move 100mm/sec or more, some even up
> to 200mm/sec or more (pushing 500IPM). The limitation is not the
> plastic parts, it is the threaded rod. Replacing those is all that
> needs (or needed once my design is released) to happen.
>
>
Discussion Thread
Kevin Martin
2011-10-09 08:24:58 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Mike Payson
2011-10-09 13:38:30 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Kevin Martin
2011-10-09 15:45:57 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Mike Payson
2011-10-09 17:57:57 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Kevin Martin
2011-10-10 07:31:23 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Mike Payson
2011-10-10 11:50:09 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Kevin Martin
2011-10-10 17:31:46 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Mike Payson
2011-10-10 18:00:39 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Alan
2011-10-10 18:00:43 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Alan
2011-10-11 12:30:50 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Kevin Martin
2011-10-11 13:01:41 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Alan
2011-10-11 14:04:01 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Jon Elson
2011-10-11 18:25:47 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Mike Payson
2011-10-11 19:02:31 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
KM6VV
2011-10-11 19:45:08 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
alenz@b...
2011-10-11 20:24:29 UTC
Re: reprap build started
KM6VV
2011-10-11 20:53:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: reprap build started
Jon Elson
2011-10-11 21:56:04 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Jon Elson
2011-10-11 21:59:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: reprap build started
Kevin Martin
2011-10-11 22:24:34 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Kevin Martin
2011-10-11 22:37:39 UTC
RE: [CAD_CAM_EDM_DRO] reprap build started
Mike Payson
2011-10-11 22:59:20 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Ron Ginger
2011-10-12 05:24:52 UTC
Re: reprap build started
Ron Thompson
2011-10-12 05:32:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: reprap build started
Dan Mauch
2011-10-12 06:41:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: reprap build started
Dan Mauch
2011-10-12 07:34:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: reprap build started
Jon Elson
2011-10-12 10:02:39 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Alan
2011-10-12 10:06:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: reprap build started
Alan
2011-10-12 11:12:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: reprap build started
Mike Payson
2011-10-12 11:24:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: reprap build started
Alan
2011-10-12 11:29:36 UTC
RE: [CAD_CAM_EDM_DRO] Re: reprap build started
Alan
2011-10-12 13:38:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: reprap build started
David G. LeVine
2011-10-15 12:25:59 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started
Jon Elson
2011-10-15 15:39:39 UTC
Re: [CAD_CAM_EDM_DRO] reprap build started