Re: [CAD_CAM_EDM_DRO] Air Powered Spindle
Posted by
Rjreese29
on 2014-10-15 12:53:33 UTC
It works great for grinding. I have a air spindle for grinding spade drills on drill blanks (cbn or diamond coated bits).
Never used it with an endmill. I would expect my air spindle to have a minimal load as in grinding, it's not a strong tool. I bought an expensive one, (but in comparing it to the harbor freight version, it is the exact same looking airtool, but we bought it in an axa tool holder( but I have never used the harbor freight version)
Hope that helps.
Rob
Hope that helps.
Rob
On Oct 15, 2014, at 10:21 AM, 'CS Mo' cs@... [CAD_CAM_EDM_DRO] <CAD_CAM_EDM_DRO@yahoogroups.com> wrote:
Does anyone have any experience using an air die grinder or similar as a high speed spindle? I need to be able to run up to a 1/4" end mill and will only have air available for power - no electricity! I'll be cutting aluminum slots that are ~1/4" wide, 1" long and 3/8" deep. I'd like to be able to cut 1/8" deep per pass, but could live with less. This will be as a live tool on a lathe - no Y control, so I can't effectively use a smaller end mill with a pocket.
--CS
Discussion Thread
2014-06-25 11:47:21 UTC
Measurements to compare machines
Andy Wander
2014-06-25 12:07:36 UTC
RE: [CAD_CAM_EDM_DRO] Measurements to compare machines
2014-06-25 12:33:18 UTC
RE: [CAD_CAM_EDM_DRO] Measurements to compare machines
2014-06-26 10:41:55 UTC
RE: [CAD_CAM_EDM_DRO] Measurements to compare machines
Michael Fagan
2014-06-26 15:26:45 UTC
Re: [CAD_CAM_EDM_DRO] Measurements to compare machines
2014-07-08 14:00:29 UTC
RE: [CAD_CAM_EDM_DRO] Measurements to compare machines
2014-07-08 14:12:23 UTC
Re: [CAD_CAM_EDM_DRO] Measurements to compare machines
2014-07-09 10:07:47 UTC
RE: [CAD_CAM_EDM_DRO] Measurements to compare machines
David G. LeVine
2014-07-09 17:16:16 UTC
Re: [CAD_CAM_EDM_DRO] Measurements to compare machines
Jon Elson
2014-07-10 09:57:08 UTC
Re: [CAD_CAM_EDM_DRO] Measurements to compare machines
ED MAISEY
2014-07-10 09:57:37 UTC
Re: [CAD_CAM_EDM_DRO] Measurements to compare machines
William Thomas
2014-07-10 13:01:18 UTC
FOAM-- [CAD_CAM_EDM_DRO] Measurements to compare machines
Gary Click
2014-07-10 20:49:29 UTC
Re: FOAM-- [CAD_CAM_EDM_DRO] Measurements to compare machines
CS Mo
2014-10-15 10:21:09 UTC
Air Powered Spindle
Hannu Venermo
2014-10-15 10:35:12 UTC
Re: [CAD_CAM_EDM_DRO] Air Powered Spindle
Rjreese29
2014-10-15 12:53:33 UTC
Re: [CAD_CAM_EDM_DRO] Air Powered Spindle
Joe Hovel
2014-10-16 08:22:09 UTC
Re: Air Powered Spindle
brock_bencomo@y...
2014-10-16 08:23:03 UTC
Re: [CAD_CAM_EDM_DRO] Air Powered Spindle
CS Mo
2014-10-16 09:01:49 UTC
Re: [CAD_CAM_EDM_DRO] Air Powered Spindle
Denis Knobloch
2014-10-16 10:36:32 UTC
Re: [CAD_CAM_EDM_DRO] Air Powered Spindle
Malcolm Parker-Lisberg
2014-10-28 04:27:34 UTC
Re: [CAD_CAM_EDM_DRO] Air Powered Spindle