Servo Motors
Posted by
William Scalione
on 1999-07-13 19:54:46 UTC
Hi,
Does anybody know of a website that gives a good description
of the inner workings of servo motors, encoders, and the drivers
needed to run them? I have the stepper stuff down pretty good but
servo motors are a whole new ballgame.I just bought a CNC lathe
with bad electronics on board, and will need to convert it using
Dan Mauch's driver board or a Servo To Go card. Would like to
read up on it before spending all my money. This CNC stuff
sure gets expensive dosen't it?
Thanks
Bill Scalione
Does anybody know of a website that gives a good description
of the inner workings of servo motors, encoders, and the drivers
needed to run them? I have the stepper stuff down pretty good but
servo motors are a whole new ballgame.I just bought a CNC lathe
with bad electronics on board, and will need to convert it using
Dan Mauch's driver board or a Servo To Go card. Would like to
read up on it before spending all my money. This CNC stuff
sure gets expensive dosen't it?
Thanks
Bill Scalione
Discussion Thread
Robert Neidorff
1999-06-14 09:08:39 UTC
Re: Servo Motors
Jon Elson
1999-06-14 13:08:36 UTC
Re: Servo Motors
William Scalione
1999-07-13 19:54:46 UTC
Servo Motors
Tim Goldstein
1999-07-13 20:57:51 UTC
RE: Servo Motors
TADGUNINC@a...
1999-07-13 21:07:37 UTC
Re: Servo Motors
IDA
2005-05-04 08:22:42 UTC
Servo Motors
Jymmm
2005-08-02 09:30:20 UTC
Servo Motors
Green, James
2005-08-02 10:14:56 UTC
RE: [CAD_CAM_EDM_DRO] Servo Motors
Stephen Wille Padnos
2005-08-02 10:29:29 UTC
Re: [CAD_CAM_EDM_DRO] Servo Motors
R Rogers
2005-08-02 10:33:25 UTC
Re: [CAD_CAM_EDM_DRO] Servo Motors
Marv Frankel
2005-08-03 01:33:32 UTC
Re: Servo Motors
Abby Katt
2005-08-03 03:31:10 UTC
CNC polishing with a mill?
turbulatordude
2005-08-03 07:35:45 UTC
Re: CNC polishing with a mill?
George Taylor, IV
2005-08-03 07:41:46 UTC
Re: [CAD_CAM_EDM_DRO] CNC polishing with a mill?
Erie Patsellis
2005-08-03 07:46:42 UTC
Re: [CAD_CAM_EDM_DRO] CNC polishing with a mill?
Abby Katt
2005-08-03 08:12:34 UTC
Re: [CAD_CAM_EDM_DRO] CNC polishing with a mill?
caedave
2005-08-03 08:18:19 UTC
Re: [CAD_CAM_EDM_DRO] CNC polishing with a mill?
Doug Pfaff
2005-08-03 08:36:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
Abby Katt
2005-08-03 08:41:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
Andy Wander
2005-08-03 08:43:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
Doug Pfaff
2005-08-03 08:44:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
Andy Wander
2005-08-03 08:46:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
turbulatordude
2005-08-03 09:14:10 UTC
Re: CNC polishing with a mill?
Jon Elson
2005-08-03 09:19:16 UTC
Re: [CAD_CAM_EDM_DRO] CNC polishing with a mill?
Jon Elson
2005-08-03 09:22:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
wanliker@a...
2005-08-03 11:45:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
Tom Hubin
2005-08-04 12:03:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC polishing with a mill?
turbulatordude
2005-08-04 16:48:19 UTC
Re: CNC polishing with a mill?