Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Posted by
salterc@v...
on 2000-11-09 05:05:56 UTC
Hello Mike,
Maybe you can help me out a little bit..
I have just purchase a Camtronics 5 amp kit from Dan along with 3 475
oz-in. steppers.
I have the controller assembled and running, the problem I am having is the
motors seem to jump around a bit or sound like they are
moving but really are not.. I have played with the software setting a good
bit(maybe that's the problem)..
I am not sure exactly of what setting to use in the software as far as
speed and travel, if this is the problem..
My steps per inch will be .0005 or 2000 steps per inch. I have tried a
couple of programs and I just cant seem to get it right.
This is my first CNC project so I am learning alot..
I do not know where to start looking for the problem,,, should I try
another cable, is the problem caused by to many steps per sec.
or to few...
I will take any help at all, and like I said this is new to me so please
make it simple.
Thanks
Chris
Maybe you can help me out a little bit..
I have just purchase a Camtronics 5 amp kit from Dan along with 3 475
oz-in. steppers.
I have the controller assembled and running, the problem I am having is the
motors seem to jump around a bit or sound like they are
moving but really are not.. I have played with the software setting a good
bit(maybe that's the problem)..
I am not sure exactly of what setting to use in the software as far as
speed and travel, if this is the problem..
My steps per inch will be .0005 or 2000 steps per inch. I have tried a
couple of programs and I just cant seem to get it right.
This is my first CNC project so I am learning alot..
I do not know where to start looking for the problem,,, should I try
another cable, is the problem caused by to many steps per sec.
or to few...
I will take any help at all, and like I said this is new to me so please
make it simple.
Thanks
Chris
Discussion Thread
Wally K
2000-11-08 17:04:26 UTC
Will Corel Draw Ver 8 convert DXF to JPG
Alan Marconett KM6VV
2000-11-08 18:00:16 UTC
Re: [CAD_CAM_EDM_DRO] Will Corel Draw Ver 8 convert DXF to JPG
Wally K
2000-11-08 18:22:46 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Alan Marconett KM6VV
2000-11-08 18:45:35 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Tom Caudle
2000-11-08 18:48:02 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Mike
2000-11-08 19:58:11 UTC
Camtronics and Sanyo-Denki Review
Randy Gordon-Gilmore
2000-11-08 22:33:16 UTC
Re: Camtronics and Sanyo-Denki Review
Mike
2000-11-09 00:42:55 UTC
Re: Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 05:05:56 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Joe Vicars
2000-11-09 05:14:59 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 06:03:07 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Joe Vicars
2000-11-09 07:08:53 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Mike
2000-11-09 10:20:27 UTC
Re: Camtronics and Sanyo-Denki Review
Chris Hellyar
2000-11-09 10:58:26 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 11:14:52 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Alan Marconett KM6VV
2000-11-09 12:57:37 UTC
Re: Camtronics and Sanyo-Denki Review
Alan Marconett KM6VV
2000-11-09 13:21:08 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review