Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Posted by
Chris Hellyar
on 2000-11-09 10:58:26 UTC
My two bits...
If you had them on the bench, and you weren't expecting them to move, they
shouldn't.... If they are "stepping" uncommanded you've more than likely
got interference problems with the cable from your PC to the controller....
Inertia and loading of the motors only effects them when they are turning...
Not enough intertia and you'll not get a good top speed out of them.
If they are 475 ounce motors, you should have problems turning the shaft
when they are on the bench powered on, and they certainly shouldn't be
"making noises". The only exception is the chopper "buzz/whistle" if the
chopper frequency is in the audio range, which would be uncommon.
Cheers, Chris.
* Design engineer, Assembly worker, Cleaner.
* Ohmark Electronics. PO Box 5302, Christchurch, New Zealand.
* http://www.ohmark.co.nz
If you had them on the bench, and you weren't expecting them to move, they
shouldn't.... If they are "stepping" uncommanded you've more than likely
got interference problems with the cable from your PC to the controller....
Inertia and loading of the motors only effects them when they are turning...
Not enough intertia and you'll not get a good top speed out of them.
If they are 475 ounce motors, you should have problems turning the shaft
when they are on the bench powered on, and they certainly shouldn't be
"making noises". The only exception is the chopper "buzz/whistle" if the
chopper frequency is in the audio range, which would be uncommon.
Cheers, Chris.
* Design engineer, Assembly worker, Cleaner.
* Ohmark Electronics. PO Box 5302, Christchurch, New Zealand.
* http://www.ohmark.co.nz
----- Original Message -----
> Yep I just had them setting on the Bench....
>
> I suppose that is the problem....
>
Discussion Thread
Wally K
2000-11-08 17:04:26 UTC
Will Corel Draw Ver 8 convert DXF to JPG
Alan Marconett KM6VV
2000-11-08 18:00:16 UTC
Re: [CAD_CAM_EDM_DRO] Will Corel Draw Ver 8 convert DXF to JPG
Wally K
2000-11-08 18:22:46 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Alan Marconett KM6VV
2000-11-08 18:45:35 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Tom Caudle
2000-11-08 18:48:02 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Mike
2000-11-08 19:58:11 UTC
Camtronics and Sanyo-Denki Review
Randy Gordon-Gilmore
2000-11-08 22:33:16 UTC
Re: Camtronics and Sanyo-Denki Review
Mike
2000-11-09 00:42:55 UTC
Re: Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 05:05:56 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Joe Vicars
2000-11-09 05:14:59 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 06:03:07 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Joe Vicars
2000-11-09 07:08:53 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Mike
2000-11-09 10:20:27 UTC
Re: Camtronics and Sanyo-Denki Review
Chris Hellyar
2000-11-09 10:58:26 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 11:14:52 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Alan Marconett KM6VV
2000-11-09 12:57:37 UTC
Re: Camtronics and Sanyo-Denki Review
Alan Marconett KM6VV
2000-11-09 13:21:08 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review