Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Posted by
Joe Vicars
on 2000-11-09 07:08:53 UTC
You can grab the shaft with your fingers (if it is a small motor) and give it a little friction. They should start operating
normally.
You will have to get them all hooked up to your load before you can home in on your accel/decel and max rpm, etc...
salterc@... wrote:
normally.
You will have to get them all hooked up to your load before you can home in on your accel/decel and max rpm, etc...
salterc@... wrote:
> Yep I just had them setting on the Bench....
>
> I suppose that is the problem....
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
Wally K
2000-11-08 17:04:26 UTC
Will Corel Draw Ver 8 convert DXF to JPG
Alan Marconett KM6VV
2000-11-08 18:00:16 UTC
Re: [CAD_CAM_EDM_DRO] Will Corel Draw Ver 8 convert DXF to JPG
Wally K
2000-11-08 18:22:46 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Alan Marconett KM6VV
2000-11-08 18:45:35 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Tom Caudle
2000-11-08 18:48:02 UTC
Re: Will Corel Draw Ver 8 convert DXF to JPG
Mike
2000-11-08 19:58:11 UTC
Camtronics and Sanyo-Denki Review
Randy Gordon-Gilmore
2000-11-08 22:33:16 UTC
Re: Camtronics and Sanyo-Denki Review
Mike
2000-11-09 00:42:55 UTC
Re: Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 05:05:56 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Joe Vicars
2000-11-09 05:14:59 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 06:03:07 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Joe Vicars
2000-11-09 07:08:53 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Mike
2000-11-09 10:20:27 UTC
Re: Camtronics and Sanyo-Denki Review
Chris Hellyar
2000-11-09 10:58:26 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
salterc@v...
2000-11-09 11:14:52 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review
Alan Marconett KM6VV
2000-11-09 12:57:37 UTC
Re: Camtronics and Sanyo-Denki Review
Alan Marconett KM6VV
2000-11-09 13:21:08 UTC
Re: [CAD_CAM_EDM_DRO] Camtronics and Sanyo-Denki Review