Re: Stepper power supplies, unregulated
Posted by
ballendo@y...
on 2000-12-03 05:14:13 UTC
Mariss wrote:
I generally Put a "bleed resistor" across the filter cap. And
(unrelated to the paragraph below) sometimes a high freq. Capacitor
as well.
There are safety standards which apply to power supplies. You might
not be subject to them as a hobbyist or one-man shop, but the advice
is still good. The goal is to be sure the supply filter caps are
drained within a relatively short time frame.
The drives "may" perform this function, but usually take much longer
than the "standard" recommmends...
Hope this helps.
Ballendo
>Roll your own. All it takes is a transformer,Bob,
>bridge rectifier and filter capacitor. The drives love it and it is
>simple and cheap.
I generally Put a "bleed resistor" across the filter cap. And
(unrelated to the paragraph below) sometimes a high freq. Capacitor
as well.
There are safety standards which apply to power supplies. You might
not be subject to them as a hobbyist or one-man shop, but the advice
is still good. The goal is to be sure the supply filter caps are
drained within a relatively short time frame.
The drives "may" perform this function, but usually take much longer
than the "standard" recommmends...
Hope this helps.
Ballendo
Discussion Thread
ballendo@y...
2000-12-03 05:14:13 UTC
Re: Stepper power supplies, unregulated
jmw@c...
2000-12-03 05:23:08 UTC
Re: Stepper power supplies, unregulated
ballendo@y...
2000-12-03 06:20:25 UTC
Re: Stepper power supplies, unregulated
Mariss Freimanis
2000-12-03 09:11:04 UTC
Re: Stepper power supplies, unregulated
Wally K
2000-12-03 09:57:11 UTC
Re: Stepper power supplies, unregulated and Zener selection
Mariss Freimanis
2000-12-03 11:24:21 UTC
Re: Stepper power supplies, unregulated and Zener selection
Wally K
2000-12-03 11:32:21 UTC
Re: Stepper power supplies, unregulated and Zener selection
Mariss Freimanis
2000-12-03 11:40:39 UTC
Re: Stepper power supplies, unregulated and Zener selection
Mike
2000-12-03 11:41:45 UTC
Bobcad 17 Review
Wally K
2000-12-03 12:13:58 UTC
Re: Stepper power supplies, unregulated and Zener selection
Smoke
2000-12-03 12:19:15 UTC
Re: [CAD_CAM_EDM_DRO] Bobcad 17 Review
Mike
2000-12-03 13:32:39 UTC
Re: Bobcad 17 Review
Smoke
2000-12-03 13:46:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bobcad 17 Review
ballendo@y...
2000-12-03 14:54:57 UTC
Re: Stepper power supplies, unregulated
Mike
2000-12-03 15:43:48 UTC
Re: Bobcad 17 Review
Mariss Freimanis
2000-12-03 17:06:46 UTC
Re: Stepper power supplies, unregulated and Zener selection
Mariss Freimanis
2000-12-03 17:17:40 UTC
Re: Stepper power supplies, unregulated
ptengin@a...
2000-12-03 19:36:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bobcad 17 Review
Mike
2000-12-03 21:00:13 UTC
Re: Bobcad 17 Review
Tim Goldstein
2000-12-03 22:56:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Bobcad 17 Review
Fred Smith
2000-12-04 03:39:56 UTC
Re:Bobcad 17 Review
ballendo@y...
2000-12-04 03:52:05 UTC
re:Re: Bobcad 17 Review
Smoke
2000-12-04 06:28:00 UTC
Re: [CAD_CAM_EDM_DRO] Re:Bobcad 17 Review
Fred Smith
2000-12-04 06:43:54 UTC
Re:Bobcad 17 Review
Smoke
2000-12-04 06:54:01 UTC
Re: [CAD_CAM_EDM_DRO] Re:Bobcad 17 Review
Wally K
2000-12-04 07:17:58 UTC
Re:Bobcad 17 Review
Tim Goldstein
2000-12-04 08:17:35 UTC
RE: [CAD_CAM_EDM_DRO] Re:Bobcad 17 Review
Fred Smith
2000-12-04 08:30:46 UTC
Re:Bobcad 17 Review
Mike
2000-12-04 10:36:06 UTC
Re: Bobcad 17 Review
Wally K
2000-12-04 12:32:40 UTC
Re:Bobcad 17 Review
Steve Greenfield
2000-12-04 13:40:30 UTC
Re: Stepper power supplies, unregulated and Zener selection
Fred Smith
2000-12-04 14:52:30 UTC
Re:Bobcad 17 Review
Smoke
2000-12-04 15:02:42 UTC
Re: [CAD_CAM_EDM_DRO] Re:Bobcad 17 Review
Wally K
2000-12-04 15:40:58 UTC
Re:Bobcad 17 Review
James Owens
2000-12-04 15:46:39 UTC
Re:Bobcad 17 Review
Fred Smith
2000-12-04 18:29:14 UTC
Re:Bobcad 17 Review