Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Posted by
Jon Elson
on 2000-12-11 22:12:25 UTC
ballendo@... wrote:
It has air bearings and some of them run to 50,000 RPM or so.
Jon
> Wally K wrote:Yes, a Kulicke & Soffa diamond saw spindle runs about $70,000!
> >With a VFD you just use a standard 3 phase motor. Unless there is
> >something here i am not understanding.
>
> When someone specifies 'spindle motor', they usually mean a motor
> design which incorporates a spindle. Typical Mfr's are Perske,
> Colombo, Elte. High grade bearings and precision balancing and
> assembly make these units pricey, and quiet in operation.
It has air bearings and some of them run to 50,000 RPM or so.
Jon
Discussion Thread
Carlos Guillermo
2000-12-11 14:24:58 UTC
spindle motors
Wally K
2000-12-11 14:38:25 UTC
Re: spindle motors
Hugh Prescott
2000-12-11 15:38:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Jon Elson
2000-12-11 16:39:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
ballendo@y...
2000-12-11 17:09:32 UTC
Re: spindle motors
Carlos Guillermo
2000-12-11 19:41:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: spindle motors
Doug Harrison
2000-12-11 19:54:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Carlos Guillermo
2000-12-11 20:02:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: spindle motors
Wally K
2000-12-11 21:03:10 UTC
Re: spindle motors
Wally K
2000-12-11 21:10:24 UTC
Re: spindle motors
Tim Goldstein
2000-12-11 21:13:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: spindle motors
ballendo@y...
2000-12-11 21:56:21 UTC
Re: Re: spindle motors
Jon Elson
2000-12-11 22:12:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
ballendo@y...
2000-12-11 22:16:10 UTC
re:Re: Re: spindle motors
ballendo@y...
2000-12-11 22:30:43 UTC
re:RE: Re: spindle motors
Carlos Guillermo
2000-12-12 06:24:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: spindle motors
Wally K
2000-12-12 10:59:01 UTC
Re: spindle motors
Smoke
2000-12-12 11:22:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Carlos Guillermo
2000-12-12 13:25:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: spindle motors
Tim Goldstein
2000-12-12 14:54:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: spindle motors
Doug Harrison
2000-12-12 16:12:44 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: Re: spindle motors
ballendo@y...
2000-12-12 16:51:24 UTC
re:rE:Re:RE: spindle motors
Jon Elson
2000-12-12 22:34:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Marcus & Eva
2000-12-13 08:22:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Jon Elson
2000-12-13 12:04:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
ballendo@y...
2000-12-13 16:28:39 UTC
Re: Re: spindle motors
Marcus & Eva
2000-12-14 08:39:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Jon Elson
2000-12-14 11:53:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Smoke
2000-12-14 12:32:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors
Marcus & Eva
2000-12-15 07:51:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: spindle motors