Re: [CAD_CAM_EDM_DRO] My CNC Project
Posted by
Rich D.
on 2001-01-05 21:10:12 UTC
Bill,
In the Vexta Motors, there are two ball bearings preloaded with a wave washer
spring. I added additional flat washers to tighten up this and take the leadscrew
thrust. So now, the handwheel end-thrust control is not needed.
I will do some serious metal removal to test this and the coupling out soon.
I agree, Sherline could do better on the leadscrew end mounting (bearings?).
Rich D.
wanliker@... wrote:
-==Rich=-=Colorado Midland Railway=-=<http://www.geocities.com/cmsteam/>
In the Vexta Motors, there are two ball bearings preloaded with a wave washer
spring. I added additional flat washers to tighten up this and take the leadscrew
thrust. So now, the handwheel end-thrust control is not needed.
I will do some serious metal removal to test this and the coupling out soon.
I agree, Sherline could do better on the leadscrew end mounting (bearings?).
Rich D.
wanliker@... wrote:
>--
> In a message dated 1/5/01 9:36:21 PM Mountain Standard Time,
> cmsteam@... writes:
>
> << If they were located on a double ended shaft motor, the leadscrew
> would not be twisted this way altho the wheels are still not doing things any
> good. >>
>
> What are you using for thrust surfaces, the original on the handwheel end? I
> am doing the reverse modification also, putting thrust bearings at the
> stepper ends of the X and Y axis, and plan to loosen up the original thrust
> system that Sherline had. I am being kind when I call there system a system.
> This might help.
> bill
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
-==Rich=-=Colorado Midland Railway=-=<http://www.geocities.com/cmsteam/>
Discussion Thread
Rich D.
2001-01-05 20:32:53 UTC
My CNC Project
wanliker@a...
2001-01-05 20:47:15 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
Rich D.
2001-01-05 21:10:12 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
wanliker@a...
2001-01-05 22:29:19 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
tauseef tahir
2001-01-06 00:38:06 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
tauseef tahir
2001-01-06 00:38:43 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
tauseef tahir
2001-01-06 00:43:31 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
Alan Marconett KM6VV
2001-01-06 10:53:45 UTC
Re: [CAD_CAM_EDM_DRO] My CNC Project
ballendo@y...
2001-01-06 21:51:50 UTC
re:Re: My CNC Project
Rich D.
2001-01-06 22:50:48 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: My CNC Project