CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] digitizer design and FAB

on 2001-01-16 11:35:04 UTC
Nothing easyer than this: Bruchstelle is point of break and soll is it must break there.
So as result the translation of Sollbruchstelle is a designed point where a piece like a
shaft conection shall break like a shear of pin.
I hope that helps you
Sven Peter

PhilC wrote:

> ----- Original Message -----
> From: "Carlos Guillermo" <carlos@...>
>
> > I wish I knew what "Sollbruchstelle" means.
>
> Babel Fish says "Break section".
>
> Phil
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager


[Non-text portions of this message have been removed]

Discussion Thread

Jon Anderson 2001-01-14 10:11:36 UTC Re: YAK (digitizer YAK at that) Tom Eldredge 2001-01-15 06:49:17 UTC Re: [CAD_CAM_EDM_DRO] Re: YAK (digitizer YAK at that) Roman Black 2001-01-15 07:53:00 UTC Re: YAK (digitizer YAK at that) Jon Anderson 2001-01-15 10:32:52 UTC Re: [CAD_CAM_EDM_DRO] Re: YAK (digitizer YAK at that) Jon Anderson 2001-01-15 10:35:18 UTC Re: [CAD_CAM_EDM_DRO] Re: YAK (digitizer YAK at that) Lee Studley 2001-01-15 10:58:48 UTC Re: YAK (digitizer YAK at that) Jon Anderson 2001-01-15 12:12:12 UTC Re: [CAD_CAM_EDM_DRO] Re: YAK (digitizer YAK at that) Carlos Guillermo 2001-01-15 18:35:27 UTC digitizer design and FAB PMeinhard@a... 2001-01-16 03:58:54 UTC Re: [CAD_CAM_EDM_DRO] digitizer design and FAB Roman Black 2001-01-16 04:46:01 UTC Re: YAK (digitizer YAK at that) Jon Anderson 2001-01-16 08:01:50 UTC [CAD_CAM_EDM_DRO] Re: YAK (digitizer YAK at that) Carlos Guillermo 2001-01-16 10:00:45 UTC RE: [CAD_CAM_EDM_DRO] digitizer design and FAB PhilC 2001-01-16 10:28:52 UTC Re: [CAD_CAM_EDM_DRO] digitizer design and FAB Sven Peter, TAD S.A. 2001-01-16 11:35:04 UTC Re: [CAD_CAM_EDM_DRO] digitizer design and FAB