CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers)

Posted by Tim Goldstein
on 2001-03-12 22:31:29 UTC
I have done a fair amount of studying of CO2 lasers and the mix is primarily
He, some N, and 5 - 8% C02. The He is essential to help conduct the heat to
the walls of the tube and to pull the CO2 to the proper energy state.

Tim
[Denver, CO]
CO2 laser optics are sitting on my desk shelf!


> I went out to a shop where a guy had an essentially home-made CO2
> laser cutting rig. It was only 50 W, I think, and was used for cutting
> plastics mostly. I think it could cut some metals if they were very thin.
> I'm awfully sure that the gas supply was high purity CO2, with nothing
> added.
>
> > I'm not sure but
> > doesn't He have a lower freezing point than N?
>
> Yes, around 4 K at atmospheric pressure. Nitrogen is 77 K. Oh, sorry,
> you CANNOT freeze Helium. It goes into a superfluid state around
> 1.3 K, but it will not solidify, no matter how cold you go. So,
> those temps
> above are the boiling points.
>
> Jon
>
> FAQ: http://www.ktmarketing.com/faq.html
>

Discussion Thread

e.heritage@b... 2001-03-11 08:51:53 UTC High pressure water jet (Lasers) Jon Elson 2001-03-11 22:09:51 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Ray 2001-03-12 08:36:30 UTC Re: High pressure water jet (Lasers) e.heritage@b... 2001-03-12 16:21:57 UTC Re: [CAD_CAM_EDM_DRO] Re: High pressure water jet (Lasers) e.heritage@b... 2001-03-12 16:45:34 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) dave engvall 2001-03-12 18:29:48 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Art Fenerty 2001-03-12 18:39:39 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) e.heritage@b... 2001-03-12 19:29:16 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) JanRwl@A... 2001-03-12 20:39:14 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Jon Elson 2001-03-12 22:13:55 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) dave engvall 2001-03-12 22:14:25 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Jon Elson 2001-03-12 22:19:01 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) dave engvall 2001-03-12 22:22:56 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Tim Goldstein 2001-03-12 22:31:29 UTC RE: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Jon Elson 2001-03-12 22:31:34 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Smoke 2001-03-12 22:48:52 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Art Fenerty 2001-03-13 07:26:38 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Art Fenerty 2001-03-13 07:28:59 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) dave engvall 2001-03-13 09:51:15 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) e.heritage@b... 2001-03-13 17:58:18 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Jon Elson 2001-03-13 21:46:43 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Jon Elson 2001-03-13 21:55:12 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) Jon Elson 2001-03-13 22:07:28 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) MIADSGNS@a... 2001-03-14 01:10:52 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers) dave engvall 2001-03-14 09:26:59 UTC Re: [CAD_CAM_EDM_DRO] High pressure water jet (Lasers)