CAD CAM EDM DRO - Yahoo Group Archive

Re: faster steppers

on 2001-03-22 11:30:53 UTC
Henrik, Ian, list,

How were you using a rate generator to MEASURE the maximum steprate?
Just by feeding the driver with a square wave? I've been trying to use
a Frequency counter designed for Amateur Radio (StarCraft?). Works part
of the time, but I suspect that the pulses (20us) may be too short for
higher speeds. I can read the frequency relatively well with an Interro
"lab scope" made for automotive testing ;>) I've also read pulse
repetitions with a 100mhz HP 'scope.

Actually, as we have a good digital signal, one should be able to count
the frequency with a program running on the PC, and using the parallel
port as an input.

You will need proper acceleration/deceleration ramps to get the maximum
speeds. AND high P.S. to coil voltage ratios (for full current) for
good "chopping".


> >I'm using steppers w/ about the same data as you driven by my
> >homebuilt drivers at 36V.
> >I can go as fast as Master5 can spit out pulses (8192 pps). Thats
> >about 1200RPM. I have tried to measure the maximum steprate with a
> >function generator but I run out of travel before the motors stall.
> >
> >You should be able to get more than 210 RPM. Maby your ways are to
> >tight?
> >What are you using as powersupply?
> >Henrik Olsson.

Discussion Thread

Henrik Olsson 2001-03-21 08:47:11 UTC Re: [CAD_CAM_EDM_DRO] faster steppers Ian Wright 2001-03-21 10:44:08 UTC Re: [CAD_CAM_EDM_DRO] faster steppers indigo_red@q... 2001-03-21 11:05:10 UTC Re: faster steppers Ian Wright 2001-03-21 15:31:19 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Paul 2001-03-21 16:15:21 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers indigo_red@q... 2001-03-21 17:09:58 UTC Re: faster steppers Jon Elson 2001-03-21 21:07:00 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers ballendo@y... 2001-03-22 07:42:37 UTC Re: faster steppers ballendo@y... 2001-03-22 08:09:03 UTC Re: faster steppers Tom Eldredge 2001-03-22 08:21:56 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Tim Goldstein 2001-03-22 08:54:48 UTC RE: [CAD_CAM_EDM_DRO] Re: faster steppers ballendo@y... 2001-03-22 09:00:34 UTC Re: faster steppers Tim Goldstein 2001-03-22 09:18:41 UTC RE: [CAD_CAM_EDM_DRO] Re: faster steppers Tim Goldstein 2001-03-22 09:22:46 UTC RE: [CAD_CAM_EDM_DRO] Re: faster steppers ballendo@y... 2001-03-22 09:35:15 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-22 11:30:53 UTC Re: faster steppers Jon Elson 2001-03-22 11:50:34 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Jon Elson 2001-03-22 12:04:22 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Henrik Olsson 2001-03-22 12:10:13 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Alan Marconett KM6VV 2001-03-22 12:12:50 UTC Re: faster steppers Jeff Demand 2001-03-22 12:24:26 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Jon Elson 2001-03-22 12:25:39 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Ian Wright 2001-03-22 12:34:56 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Henrik Olsson 2001-03-22 12:40:16 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Tim Goldstein 2001-03-22 12:42:18 UTC RE: [CAD_CAM_EDM_DRO] Re: faster steppers Alan Marconett KM6VV 2001-03-22 15:08:43 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-22 15:13:30 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-22 15:14:48 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-22 15:33:06 UTC Re: faster steppers Smoke 2001-03-22 15:48:09 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Tim Goldstein 2001-03-22 15:49:53 UTC RE: [CAD_CAM_EDM_DRO] Re: faster steppers Smoke 2001-03-22 16:13:17 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers ballendo@y... 2001-03-22 16:16:53 UTC Re: faster steppers ballendo@y... 2001-03-22 17:27:07 UTC speed determination was Re: faster steppers Alan Marconett KM6VV 2001-03-22 17:48:34 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-22 17:52:56 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-22 18:52:44 UTC Re: [CAD_CAM_EDM_DRO] speed determination was Re: faster steppers Ian Wright 2001-03-23 01:23:30 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Tom Eldredge 2001-03-23 07:03:09 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers beer@s... 2001-03-23 09:26:43 UTC Re: faster steppers Henrik Olsson 2001-03-23 10:22:44 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Paul 2001-03-23 15:14:50 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Alan Marconett KM6VV 2001-03-23 15:50:13 UTC Re: faster steppers Jon Elson 2001-03-23 15:58:25 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers Alan Marconett KM6VV 2001-03-23 16:21:58 UTC Re: faster steppers Alan Marconett KM6VV 2001-03-23 16:38:50 UTC Re: faster steppers Henry Palonen 2001-03-24 06:34:54 UTC Re: faster steppers (and Eagle PCB output) Alan Marconett KM6VV 2001-03-24 12:40:28 UTC Re: faster steppers (and Eagle PCB output) ballendo@y... 2001-03-24 21:25:49 UTC Re: faster steppers Henry Palonen 2001-03-25 07:04:18 UTC Re: [CAD_CAM_EDM_DRO] Re: faster steppers (and Eagle PCB output)