CAD CAM EDM DRO - Yahoo Group Archive

Re: Wire EDM

Posted by F. de Beer
on 1999-09-23 00:20:01 UTC
I have been told that the wire before it travels to the work, is pulled
through a stone to get a perfect round profile.

Frank de Beer




>
> No, I don't think they rotate the wire. After one pass, the wire is
discarded, usually.
> They use a LOT of wire, so it doesn't stay in one place very long before
it is past
> the area where cutting is going on.
>
> As for autothreading, some machines have this, it sounds pretty tricky.
>
> Jon
>

>

Discussion Thread

David Howland 1999-09-22 11:56:43 UTC Wire EDM Jon Elson 1999-09-22 13:46:43 UTC Re: Wire EDM Ian Wright 1999-09-22 14:32:58 UTC Re: Wire EDM gullo@e... 1999-09-22 21:13:38 UTC Re: Wire EDM F. de Beer 1999-09-23 00:20:01 UTC Re: Wire EDM chevalier121 2002-05-23 08:54:03 UTC Wire EDM Lalit Sahni 2002-05-24 10:25:32 UTC Re: [CAD_CAM_EDM_DRO] Wire EDM Ian W. Wright 2002-05-25 05:27:33 UTC Re: [CAD_CAM_EDM_DRO] Wire EDM Carlos Guillermo 2002-05-25 06:24:07 UTC RE: [CAD_CAM_EDM_DRO] Wire EDM chevalier121 2002-05-28 06:22:01 UTC Re: Wire EDM Steve Ross 2002-05-28 06:32:36 UTC Flashcut on a taig mill bjammin@i... 2002-05-28 07:02:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire EDM Dan Mauch 2002-05-28 08:34:54 UTC Dyna Myte CNC Desk Top Interface Console Andrew Werby 2002-05-28 13:39:46 UTC Flashcut on a taig mill Tony Jeffree 2002-05-28 23:24:28 UTC Re: Flashcut on a taig mill chevalier121 2002-05-29 02:43:58 UTC Re: Wire EDM turbulatordude 2002-05-29 04:13:30 UTC Re: Wire EDM Andrew Werby 2002-05-29 09:44:40 UTC Re: Flashcut on a taig mill Jon Elson 2002-05-29 10:26:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire EDM Jon Elson 2002-05-29 10:30:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire EDM tonyjeffree 2002-05-29 11:06:44 UTC Re: Flashcut on a taig mill Mark Fraser 2002-05-29 16:27:12 UTC Wire EDM paoli_60175 2002-07-08 17:26:01 UTC Re: Wire EDM Carlos Guillermo 2002-07-08 20:43:04 UTC RE: [CAD_CAM_EDM_DRO] Re: Wire EDM Jon Elson 2002-07-08 22:02:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire EDM John Archibald 2004-09-10 19:45:58 UTC Wire EDM Jon Elson 2004-09-10 23:07:47 UTC Re: [CAD_CAM_EDM_DRO] Wire EDM Thomas J Powderly 2006-04-03 10:43:40 UTC Re: Wire EDM Graham Stabler 2006-04-03 13:13:54 UTC Re: Wire EDM jesse Brennan 2006-04-03 14:05:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire EDM Graham Stabler 2006-04-03 17:55:20 UTC Re: Wire ECM jesse Brennan 2006-04-03 18:07:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire ECM Graham Stabler 2006-04-04 04:20:04 UTC Re: Wire ECM juan gelt 2006-04-04 08:23:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Wire ECM Graham Stabler 2006-04-04 09:00:59 UTC Re: Wire ECM