Re: What does everybody use...
Posted by
Dan Mauch
on 1999-05-20 06:50:57 UTC
see www.seanet.com/~dmauch for my web page.
-----Original Message-----
From: Ward Merkouris <ward@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Wednesday, May 19, 1999 7:40 PM
Subject: Re: [CAD_CAM_EDM_DRO] What does everybody use...
-----Original Message-----
From: Ward Merkouris <ward@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Wednesday, May 19, 1999 7:40 PM
Subject: Re: [CAD_CAM_EDM_DRO] What does everybody use...
>From: Ward Merkouris <ward@...>signals are TTL level step and direction for each of the four
>
>I am also using Artisan 3.2. It does use a special board, but the output
>axis drives. I'm not familiar with Dan Mauch driver boards. What arethey, and where can I find out more about them? I am currently
>considering the purchase of Digital Design Technologies' three axismicrostepping driver box. It will run up to 3 amp motors and is quite
>reasonably priced. I haven't actually seen one yet, so I don't know muchmore about it than this.
>interface boards BUT early SW (ver3 etc 1994) would run off the
>Ward M.
>
>
>
>Brian Fairey wrote:
>
>> From: Brian Fairey <bfairey@...>
>>
>> No I dont think so as the most recent Artisan and Pro SW use AHHA's own
>> parallel port.Mauch driver board and the AHHA software(very early style using
>> Brian.
>>
>> John Stevenson wrote:
>>
>> > From: john@... (John Stevenson)
>> >
>> > On Wed, 19 May 1999 16:12:45 -0400, you wrote:
>> >
>> > >From: Brian Fairey <bfairey@...>
>> > >
>> > >Ward, I also use AHHA gear and also plan to do a lathe using a Dan
>> > >the parallel port)boards??
>> > >Brian, Ont, Canada.
>> >
>> > Brian,
>> > Any chance on some more details of using the Ahha software with Dan's
>> > I also run Ahha and would be interested in going this way for a smallmissed the previous messages, I'm wondering if the extra
>> > positioning table.
>> > Can you use the later software for Artisan. I have version 3.2
>> >
>> > >Ward Merkouris wrote:
>> > >
>> > >> From: Ward Merkouris <ward@...>
>> > >>
>> > >> Hi Jon,
>> > >>
>> > >> I'm new to the list, this is the first message received. As I have
>> > >> boards you have made are for stepper motors or DC motors withencoders.
>> > >>interested in obtaining another set of motor drivers and
>> > >> I currently have an AHHA setup (4 axis) on a small bed mill but am
>> > >> motors for use on a small lathe. The AHHA software and board issuesstep and direction signals oa TTL level. Would your boards
>> > >> be compatible with this?discussion of shop built systems in the above catagories.
>> > >>
>> >
>> > Regards,
>> > John Stevenson
>> > Nottingham, England
>> >
>>
> ------------------------------------------------------------------------
>> > It's finally here! What's your opinion?
>> > http://www.onelist.com
>> > Create a Star Wars discussion group at ONElist.
>>
> ------------------------------------------------------------------------
>> > welcome to CAD_CAM_EDM_DRO@..., an unmodulated list for the
>>discussion of shop built systems in the above catagories.
>> ------------------------------------------------------------------------
>> How many communities do you think join ONElist each day?
>> http://www.onelist.com
>> More than 1,000! Create yours now!
>> ------------------------------------------------------------------------
>> welcome to CAD_CAM_EDM_DRO@..., an unmodulated list for the
>discussion of shop built systems in the above catagories.
>
>------------------------------------------------------------------------
>With more than 17 million e-mails exchanged daily...
>http://www.onelist.com
>...ONElist is THE place where the world talks!
>------------------------------------------------------------------------
>welcome to CAD_CAM_EDM_DRO@..., an unmodulated list for the
>
Discussion Thread
Don Hughes
1999-05-16 23:25:03 UTC
What does everybody use...
john@x...
1999-05-17 00:12:26 UTC
Re: What does everybody use...
Don Hughes
1999-05-17 00:55:50 UTC
Re: What does everybody use...
Jonty50@x...
1999-05-17 10:51:54 UTC
Re: What does everybody use...
Don Hughes
1999-05-17 11:08:23 UTC
Re: What does everybody use...
Tim Goldstein
1999-05-17 12:00:40 UTC
Re: What does everybody use...
garfield@x...
1999-05-17 13:15:48 UTC
Re: What does everybody use...
Jon Elson
1999-05-17 13:32:26 UTC
Re: What does everybody use...
Al Schoepp
1999-05-17 13:37:19 UTC
Re: What does everybody use...
Tim Goldstein
1999-05-17 16:19:42 UTC
Re: What does everybody use...
Bruce
1999-05-18 04:22:27 UTC
Re: What does everybody use...
Don Hughes
1999-05-18 07:41:00 UTC
Re: What does everybody use...
Jonty50@x...
1999-05-18 07:57:37 UTC
Re: What does everybody use...
Don Hughes
1999-05-18 08:06:26 UTC
Re: What does everybody use...
Jonty50@x...
1999-05-18 10:50:38 UTC
Re: What does everybody use...
Jonty50@x...
1999-05-18 10:57:34 UTC
Re: What does everybody use...
Jon Elson
1999-05-18 11:57:06 UTC
Re: What does everybody use...
Dan Mauch
1999-05-18 13:39:51 UTC
Re: What does everybody use...
Jon Elson
1999-05-18 22:10:52 UTC
Re: What does everybody use...
Ward Merkouris
1999-05-18 22:23:09 UTC
Re: What does everybody use...
Jon Elson
1999-05-19 12:19:18 UTC
Re: What does everybody use...
Brian Fairey
1999-05-19 13:12:45 UTC
Re: What does everybody use...
john@x...
1999-05-19 14:59:57 UTC
Re: What does everybody use...
Brian Fairey
1999-05-19 16:45:48 UTC
Re: What does everybody use...
Ward Merkouris
1999-05-19 19:43:45 UTC
Re: What does everybody use...
Dan Mauch
1999-05-20 06:30:48 UTC
Re: What does everybody use...
Dan Mauch
1999-05-20 06:50:57 UTC
Re: What does everybody use...
Dan Mauch
1999-05-20 07:06:13 UTC
Re: What does everybody use...