CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Tool up

on 2001-09-15 18:04:26 UTC
Thank you very much for the help, how long have you been collecting all this
milling stuff J. S.? I have actually read just about everything there is on
the internet about the mill, of which there is not much. I have seen it
listed atleast four times as the VBRP, even on www.lathes.co.uk . I was told
Beaver was bought by a US company which is why there is so little
information about them. At the auction I was at a few weeks back they had a
Beaver Pal with a case of tooling and a lion painted on where it's wood
chewing partner used to be on it's side. Looking at BVRP I'm seeing the
smoke clear, BVRP = BeaVeR Pal. Somewhere along the lines there has been a
mix up. The mill looked incredibly solid and was by far the least worn one
there. The BVRP (Which now opens the doorway to lots more 'net searching)
comes as a 40 or 30 I read. Where abouts are you John? How much does a new
set of ballscrews cost for a mill of this size out of interest? I am sitting
down. : )

John Heritage

John,
Here's a picture of a Beaver BVRP
http://www.zhongyang-engrg.com/catalog/me9954.htm
They are 10" x 48" table machines with a 40 Int spindle taper. Same
build up as a Bridgeport but a *lot* stronger. Motor is usually 4 or
5 Hp 440v 3 phase, but I have seen these with 3Hp single phase fitted.
Brand new ER32 collet chucks cost 35 pounds each at the moment.
Somewhere kicking about I have a box of 20 plus pieces of 40 int
tooling that's going spare. Most have closer nuts missing and there
are only a few collets.
I even have spare X and Y axis ball screws for one of these with the
motor mounts and bearings.
Although some one was interestd in the Y axis screw.

John Stevenson


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

info.host@b... 2001-09-15 13:47:58 UTC Tool up machines@n... 2001-09-15 17:31:05 UTC Re: Tool up info.host@b... 2001-09-15 18:04:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Tool up Sven Peter 2001-09-15 20:03:41 UTC Re: [CAD_CAM_EDM_DRO] Tool up Les Newell 2001-09-16 02:23:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Tool up info.host@b... 2001-09-16 03:02:36 UTC Re: [CAD_CAM_EDM_DRO] Tool up machines@n... 2001-09-16 04:26:58 UTC Re: Tool up machines@n... 2001-09-16 04:49:08 UTC Re: Tool up info.host@b... 2001-09-16 05:44:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Tool up machines@n... 2001-09-16 06:18:30 UTC Re: Tool up Sven Peter 2001-09-16 07:59:22 UTC Re: [CAD_CAM_EDM_DRO] Tool up Sven Peter 2001-09-16 07:59:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Tool up Sven Peter 2001-09-16 07:59:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Tool up Smoke 2001-09-16 08:08:01 UTC Re: [CAD_CAM_EDM_DRO] Tool up Jon Elson 2001-09-17 01:00:11 UTC Re: [CAD_CAM_EDM_DRO] Tool up Jon Elson 2001-09-17 01:01:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Tool up