CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] EMC Lathe mode.

Posted by Doug Fortune
on 2001-10-02 07:22:19 UTC
Art Fenerty wrote:

> From the software's point of view, I think one pulse would do. Afetr all,
> the spindle is not changing speeds fast enough to disturb the mathmatics.
> If you time the distance between pulses, you can figure out where the
> spindle actually is at all times I would think.

Yes, a single pulse per rev gets you 90% there (the other 10%
functionality
and performance takes a lot more work).

I can send you some canned cycle faxes off-line.

Doug
http://www.cncKITS.com

Discussion Thread

Art Fenerty 2001-10-01 17:28:52 UTC EMC Lathe mode. Doug Fortune 2001-10-01 17:50:47 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Art Fenerty 2001-10-01 17:58:53 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. wanliker@a... 2001-10-01 18:20:05 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Doug Fortune 2001-10-01 19:29:07 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. currinh@O... 2001-10-01 19:59:01 UTC Re: EMC Lathe mode. wanliker@a... 2001-10-01 21:27:04 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-01 22:27:26 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-01 22:30:39 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-01 22:32:29 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-01 22:38:41 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Brian Pitt 2001-10-02 02:13:35 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Art Fenerty 2001-10-02 04:49:58 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Doug Fortune 2001-10-02 07:22:19 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-02 10:46:54 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Ethan Vos 2001-10-02 10:58:41 UTC RE: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-02 11:00:51 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Brian Pitt 2001-10-02 11:41:54 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Paul 2001-10-02 12:11:28 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Art Fenerty 2001-10-02 12:19:07 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Ray 2001-10-02 13:48:44 UTC Re: Re: EMC Lathe mode. jhtkcarn@a... 2001-10-02 14:21:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC Lathe mode. beer@s... 2001-10-02 14:40:22 UTC Re: Re: EMC Lathe mode. ccs@m... 2001-10-02 14:58:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC Lathe mode. Art Fenerty 2001-10-02 15:24:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC Lathe mode. Fred Smith 2001-10-02 15:57:59 UTC Re: EMC Lathe mode. Art Fenerty 2001-10-02 16:06:37 UTC Re: [CAD_CAM_EDM_DRO] Re: EMC Lathe mode. Jon Elson 2001-10-02 20:09:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC Lathe mode. Jon Elson 2001-10-02 20:53:24 UTC Re: [CAD_CAM_EDM_DRO] EMC Lathe mode. Jon Elson 2001-10-02 21:04:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: EMC Lathe mode. Donald Brock 2001-10-03 02:52:39 UTC Re: EMC Lathe mode.