Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Posted by
Weyland
on 2001-10-14 15:38:00 UTC
Hey Doug~!
From: "Doug Fortune" <pentam@...>
I have Gecko 210s.
What does "operate using GND only" mean?
Weyland
From: "Doug Fortune" <pentam@...>
> If you use a Gecko 201 or 320 you need +5V fromThis seems to be where some of my confusion is coming from.
> somewhere (the Gecko 210 or 340 can operate using GND
> only).
I have Gecko 210s.
What does "operate using GND only" mean?
> The parallel port does not have +5V available, butAhhh...okay.
> you can inject +5V into the parallel cable using a
> suitable card (such as my pBreak parallel port breakout
> board), using one of the redundant line 18-25 GND
> lines at the computer end. In this case, line 25 is
> arbitrarily reserved for +5V, and this allows you
> access to +5V at the equipment end.
> See my webpage (or Tim's Parallel Port info page)Okeydoke.
> for a graphic of the possibilities.
Weyland
Discussion Thread
Weyland
2001-10-14 15:05:09 UTC
Gecko power requirements
Doug Fortune
2001-10-14 15:29:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 15:38:00 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Tim Goldstein
2001-10-14 15:39:34 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
Doug Fortune
2001-10-14 15:55:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 16:13:18 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
HighTech
2001-10-14 18:11:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:22:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:27:27 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-14 22:17:25 UTC
Re: Gecko power requirements
Jon Elson
2001-10-14 22:52:14 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Alan Marconett KM6VV
2001-10-15 10:19:04 UTC
Gecko power requirements
Weyland
2001-10-16 13:54:06 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-16 14:25:17 UTC
Re: Gecko power requirements
Alan Marconett KM6VV
2001-10-16 14:27:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-16 15:07:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
ccs@m...
2001-10-17 10:30:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Weyland
2001-10-18 15:09:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Doug Fortune
2001-10-18 17:30:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements