CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements

Posted by Weyland
on 2001-10-16 15:07:46 UTC
From: <mariss92705@...>

> Weland,
>
> You might want to re-think this. The +5VDC ground must be common to
> your PC, not the motor power supply ground. The easiest place to pick
> up +5VDC from your computer is from pin 1 on the game port (DB 17
> connector).
>
> Mariss

Ahhhhh...damn...knew it was too easy...

Well, awright.
I was just going for that ultra clean look, having no extra wires in sight.

So, with that in mind, I got to thinking.
(**DANGER**)
Since the parallel port on this specific motherboard actually comes off
a header and travels via ribbon cable to the connector the external cable
goes to,
would it be feasible for me to strip out the 25th pin's wire and splice it
to
a +5V source from the computer's power supply?

That would keep things clean.

Thanks Mariss~!

Weyland

Discussion Thread

Weyland 2001-10-14 15:05:09 UTC Gecko power requirements Doug Fortune 2001-10-14 15:29:17 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements Weyland 2001-10-14 15:38:00 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements Tim Goldstein 2001-10-14 15:39:34 UTC RE: [CAD_CAM_EDM_DRO] Gecko power requirements Doug Fortune 2001-10-14 15:55:57 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements Weyland 2001-10-14 16:13:18 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements HighTech 2001-10-14 18:11:40 UTC RE: [CAD_CAM_EDM_DRO] Gecko power requirements JanRwl@A... 2001-10-14 18:22:58 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements JanRwl@A... 2001-10-14 18:27:27 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements mariss92705@y... 2001-10-14 22:17:25 UTC Re: Gecko power requirements Jon Elson 2001-10-14 22:52:14 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements Alan Marconett KM6VV 2001-10-15 10:19:04 UTC Gecko power requirements Weyland 2001-10-16 13:54:06 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements mariss92705@y... 2001-10-16 14:25:17 UTC Re: Gecko power requirements Alan Marconett KM6VV 2001-10-16 14:27:21 UTC Re: [CAD_CAM_EDM_DRO] Gecko power requirements Weyland 2001-10-16 15:07:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements ccs@m... 2001-10-17 10:30:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements Weyland 2001-10-18 15:09:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements Doug Fortune 2001-10-18 17:30:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements