Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Posted by
Weyland
on 2001-10-18 15:09:09 UTC
From: <ccs@...>
for EMC and have no plans for a printer on it.
If I do, I can always install another port.
splice it to an unused pin on the DB25.
Weyland
>cable
> > Since the parallel port on this specific motherboard actually comes off
> > a header and travels via ribbon cable to the connector the external
> > goes to,it
> > would it be feasible for me to strip out the 25th pin's wire and splice
> > toNot a problem since I built the computer strictly
> > a +5V source from the computer's power supply?
>
> Sure, until someone plugs in a printer...
for EMC and have no plans for a printer on it.
If I do, I can always install another port.
> You should probably fuse it, with a small (100 ma?) fuse, too. SomeThis is what I was thinking, to use a spare power wire and
> computer power supplies (Dell) have zero tolerance for short
> circuits... don't ask me how I know (and it had non-standard wiring,
> so I had to make a new harness for the replacement). Get your
> power off a spare disk power cable, not the motherboard!
splice it to an unused pin on the DB25.
Weyland
Discussion Thread
Weyland
2001-10-14 15:05:09 UTC
Gecko power requirements
Doug Fortune
2001-10-14 15:29:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 15:38:00 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Tim Goldstein
2001-10-14 15:39:34 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
Doug Fortune
2001-10-14 15:55:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 16:13:18 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
HighTech
2001-10-14 18:11:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:22:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:27:27 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-14 22:17:25 UTC
Re: Gecko power requirements
Jon Elson
2001-10-14 22:52:14 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Alan Marconett KM6VV
2001-10-15 10:19:04 UTC
Gecko power requirements
Weyland
2001-10-16 13:54:06 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-16 14:25:17 UTC
Re: Gecko power requirements
Alan Marconett KM6VV
2001-10-16 14:27:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-16 15:07:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
ccs@m...
2001-10-17 10:30:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Weyland
2001-10-18 15:09:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Doug Fortune
2001-10-18 17:30:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements