Re: Gecko power requirements
Posted by
mariss92705@y...
on 2001-10-16 14:25:17 UTC
Weland,
You might want to re-think this. The +5VDC ground must be common to
your PC, not the motor power supply ground. The easiest place to pick
up +5VDC from your computer is from pin 1 on the game port (DB 17
connector).
Mariss
You might want to re-think this. The +5VDC ground must be common to
your PC, not the motor power supply ground. The easiest place to pick
up +5VDC from your computer is from pin 1 on the game port (DB 17
connector).
Mariss
> Thanks Alan, but I think I stumbled across the solution last night.the other
> They got these here things called "regulators".
> I just learned m'self 'bout'm.
> Ya put yer voltage in one side, and the desired voltage comes out
> side.again.
> Whooda thunk it?
>
> Anyway, looks like I can built another little circuit board with
> two of these things (one for 5V and one for 12V) and I'll be fine.
> (looks like an under $20 project)
>
> I think I might be gettin' the hang of this stuff finally...
>
> Problem is, I think I've been infected with whatever's goin' 'round.
> Just when I think I've finished something (like the power supply)
> another idea or discovery pops into view and I'm off and runnin'
>worried...
> The kitchen table isn't visible anymore, and the wife's gettin'
>
> Weyland
Discussion Thread
Weyland
2001-10-14 15:05:09 UTC
Gecko power requirements
Doug Fortune
2001-10-14 15:29:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 15:38:00 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Tim Goldstein
2001-10-14 15:39:34 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
Doug Fortune
2001-10-14 15:55:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 16:13:18 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
HighTech
2001-10-14 18:11:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:22:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:27:27 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-14 22:17:25 UTC
Re: Gecko power requirements
Jon Elson
2001-10-14 22:52:14 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Alan Marconett KM6VV
2001-10-15 10:19:04 UTC
Gecko power requirements
Weyland
2001-10-16 13:54:06 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-16 14:25:17 UTC
Re: Gecko power requirements
Alan Marconett KM6VV
2001-10-16 14:27:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-16 15:07:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
ccs@m...
2001-10-17 10:30:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Weyland
2001-10-18 15:09:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Doug Fortune
2001-10-18 17:30:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements