Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Posted by
Weyland
on 2001-10-16 13:54:06 UTC
From: "Alan Marconett KM6VV" <KM6VV@...>
Thanks Alan, but I think I stumbled across the solution last night.
They got these here things called "regulators".
I just learned m'self 'bout'm.
Ya put yer voltage in one side, and the desired voltage comes out the other
side.
Whooda thunk it?
Anyway, looks like I can built another little circuit board with
two of these things (one for 5V and one for 12V) and I'll be fine.
(looks like an under $20 project)
I think I might be gettin' the hang of this stuff finally...
Problem is, I think I've been infected with whatever's goin' 'round.
Just when I think I've finished something (like the power supply)
another idea or discovery pops into view and I'm off and runnin' again.
The kitchen table isn't visible anymore, and the wife's gettin' worried...
Weyland
> Hi Weyland,LOL!
>
> You shouldn't get it FROM the parallel port, Try the joystick port or
> the keyboard port. Even a wall-wart.
>
> Alan KM6VV
Thanks Alan, but I think I stumbled across the solution last night.
They got these here things called "regulators".
I just learned m'self 'bout'm.
Ya put yer voltage in one side, and the desired voltage comes out the other
side.
Whooda thunk it?
Anyway, looks like I can built another little circuit board with
two of these things (one for 5V and one for 12V) and I'll be fine.
(looks like an under $20 project)
I think I might be gettin' the hang of this stuff finally...
Problem is, I think I've been infected with whatever's goin' 'round.
Just when I think I've finished something (like the power supply)
another idea or discovery pops into view and I'm off and runnin' again.
The kitchen table isn't visible anymore, and the wife's gettin' worried...
Weyland
Discussion Thread
Weyland
2001-10-14 15:05:09 UTC
Gecko power requirements
Doug Fortune
2001-10-14 15:29:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 15:38:00 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Tim Goldstein
2001-10-14 15:39:34 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
Doug Fortune
2001-10-14 15:55:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-14 16:13:18 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
HighTech
2001-10-14 18:11:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:22:58 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
JanRwl@A...
2001-10-14 18:27:27 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-14 22:17:25 UTC
Re: Gecko power requirements
Jon Elson
2001-10-14 22:52:14 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Alan Marconett KM6VV
2001-10-15 10:19:04 UTC
Gecko power requirements
Weyland
2001-10-16 13:54:06 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
mariss92705@y...
2001-10-16 14:25:17 UTC
Re: Gecko power requirements
Alan Marconett KM6VV
2001-10-16 14:27:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko power requirements
Weyland
2001-10-16 15:07:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
ccs@m...
2001-10-17 10:30:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Weyland
2001-10-18 15:09:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements
Doug Fortune
2001-10-18 17:30:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko power requirements