CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Drilling with Vector

on 2002-01-13 17:36:50 UTC
Golly Gee! When I started this thread, I thought I was asking a stupid
question. Just goes to prove, there aren't any.
Dave Goodfellow

----- Original Message -----
From: Tim Goldstein <timg@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Sunday, January 13, 2002 4:32 PM
Subject: RE: [CAD_CAM_EDM_DRO] Re: Drilling with Vector


>
>
> > -----Original Message-----
>
> > >Fred, Two people who use Vector say you have to manually edit the
> > >cycle codes.
>
> Put me down as one of the two that just learned a new way to do it without
> manual edit.
>
> > I also use Vector . I just put points where I want to drill the holes,
> > either at the depth I want the hole to go to or all at z=0 and
> > then cut and
> > paste them to the desired depth. After inserting NC select Cycle and
> > select the G83 peck cycle. Highlight the drawing window and generate
the
> > NC. A macro then asks for the clearance plane, peck depth and
> > feedrate. Seems to work for me, don't know if this is the best
> > or only way
> > of doing it.
>
> Thanks for pointing this out. I was happy doing the manual edit, but this
is
> sure a lot faster.
>
> Tim
> [Denver, CO]
>
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

Discussion Thread

David Goodfellow 2002-01-13 11:07:36 UTC Drilling with Vector Tim Goldstein 2002-01-13 11:36:47 UTC RE: [CAD_CAM_EDM_DRO] Drilling with Vector imserv1 2002-01-13 11:48:21 UTC Re: Drilling with Vector Carol & Jerry Jankura 2002-01-13 11:49:52 UTC RE: [CAD_CAM_EDM_DRO] Drilling with Vector David Goodfellow 2002-01-13 12:12:45 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector David Goodfellow 2002-01-13 12:20:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Drilling with Vector David Goodfellow 2002-01-13 12:24:06 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector follicely_challenged 2002-01-13 12:25:15 UTC Re: Drilling with Vector imserv1 2002-01-13 13:05:15 UTC Re: Drilling with Vector follicely_challenged 2002-01-13 13:09:55 UTC Re: Drilling with Vector David Goodfellow 2002-01-13 14:16:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Drilling with Vector stevenson_engineers 2002-01-13 14:53:32 UTC Re: Drilling with Vector Smoke 2002-01-13 14:55:37 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector Al Schoepp 2002-01-13 15:06:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Drilling with Vector Smoke 2002-01-13 15:16:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Drilling with Vector Alan Marconett KM6VV 2002-01-13 16:07:55 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector Tim Goldstein 2002-01-13 16:32:07 UTC RE: [CAD_CAM_EDM_DRO] Re: Drilling with Vector imserv1 2002-01-13 17:03:14 UTC Re: Drilling with Vector Carol & Jerry Jankura 2002-01-13 17:28:00 UTC RE: [CAD_CAM_EDM_DRO] Re: Drilling with Vector David Goodfellow 2002-01-13 17:33:22 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector David Goodfellow 2002-01-13 17:36:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Drilling with Vector stevenson_engineers 2002-01-14 00:50:45 UTC Re: Drilling with Vector Alan Marconett KM6VV 2002-01-14 11:07:04 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector Al Schoepp 2002-01-19 08:09:21 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector Alan Marconett KM6VV 2002-01-19 13:05:37 UTC Re: [CAD_CAM_EDM_DRO] Drilling with Vector