CAD CAM EDM DRO - Yahoo Group Archive

Re: Spindle motor drive belts MAXNC 10 UPDATE

Posted by hansw
on 1999-11-05 10:12:50 UTC
Jon,
I understand about the starting from scratch, but have 1.5-1.7 K$ in
this setup and as much as I want to trash it, I'll first have to squeeze
a few hours of work out of it...
Anyway, as you are the first person I know that converted the MAXNC for
ball screws. if you have the time to make a few photo's and perhaps a
few part numbers ( lead screw material and supplier of the ball screws
you used) it would help a lot.

I was also in doubt about the anodize to anodize surface, and make sure
I keep a liberal amount of grease on these...

With such a large surface area, would Teflon strips do the trick !

Hans Wedemeyer


Jon Anderson wrote:

> Hans,
>
> The through hole in the saddle isn't 3/8 all the way through. To run a
> ball screw will require drilling slightly over size for clearance,
> plus
> fabrication of mounting plates like I did for the ActiveCam nuts. It's
> doable, but I passed on the cost because of how finicky the ways are
> for
> adjustment. I think I've struck a fairly reasonable compromise in
> accuracy vs cost.
> One thing I've considered but not tried, is to bond .002 shim stock to
> the long slides to get away from the anodized/anodized interface, and
> use maybe a teflon impregnated material for gib strips. I've found
> that
> there is a -very- fine line between proper adjustment and binding.
>
> There comes point when it's just easier to start from scratch...
>
> Jon
>
> ------------------------------------------------------------------------
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes
> there.
> For the FAQ, go to http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
> ----------------------------------------------------------------
> [Image]
> Click Here
>

Discussion Thread

hansw 1999-11-04 13:27:19 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Jon Anderson 1999-11-04 16:14:43 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-04 18:41:50 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Jon Anderson 1999-11-04 19:01:49 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Dan Mauch 1999-11-05 06:48:37 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 08:00:35 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Jon Anderson 1999-11-05 08:58:10 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 09:17:49 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Jon Anderson 1999-11-05 09:59:22 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Darrell Gehlsen 1999-11-05 10:08:46 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 10:12:50 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 10:33:04 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Darrell Gehlsen 1999-11-05 10:39:40 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE drew@x... 1999-11-05 10:39:50 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Andrew Werby 1999-11-05 02:50:54 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE Jon Anderson 1999-11-05 11:53:11 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 12:14:38 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Ian Wright 1999-11-05 15:09:16 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Steve Carlisle 1999-11-05 17:18:22 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 17:15:21 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Andrew Werby 1999-11-05 10:26:17 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-05 19:34:07 UTC Re: Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Ian Wright 1999-11-06 14:57:40 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-06 17:20:43 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Ian Wright 1999-11-07 05:05:47 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-07 10:15:11 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE George Potter 1999-11-07 11:10:47 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE hansw 1999-11-07 11:46:03 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Ian Wright 1999-11-07 15:39:11 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Darrell Gehlsen 1999-11-07 23:55:29 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Marshall Pharoah 1999-11-08 04:41:18 UTC Re: Re: Spindle motor drive belts MAXNC 10 UPDATE Paul Devey 1999-11-09 14:26:44 UTC Re: Spindle motor drive belts MAXNC 10 UPDATE