Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Posted by
Alan Marconett KM6VV
on 2002-02-13 22:36:22 UTC
Hi Brian,
Instead of the buttons, you could use another encoder, but the cost goes
up an encoder could be shared by the feed and spindle menus. I haven't
seen a "Dx to go" display, I just watch the numbers spin! As a
programmed menu, the overrides could be anything you want.
Alan KM6VV
Brian Pitt wrote:
Instead of the buttons, you could use another encoder, but the cost goes
up an encoder could be shared by the feed and spindle menus. I haven't
seen a "Dx to go" display, I just watch the numbers spin! As a
programmed menu, the overrides could be anything you want.
Alan KM6VV
Brian Pitt wrote:
>
> Hi Alan
>
> oh yea sixteen is plenty ,I would rather have them on a knob than
> have to use buttons to scroll thru them but scrolling would be OK
> for the spindle speed override (it dosent get used as much)
>
> the feedrate override knob comes in handy when you do the first run to
> verify programs ,you set the machine to single block and turn the feed to
> zero ,then step thru watching the 'distance-to-go' display and crank up
> the feed knob after checking that the current move wont crash
>
> many controls have somewhat odd steps on the overrides like
> 0-5-10-25-50-60-70-80%... and so on up to 200% within 16 settings
>
> others have three overrides for spindle-speed,feedrate and rapid-feedrate
> with rapid settings for 25-50-75-100% the rapid override can be dangerous
> if your not used to it ,I'm not... ,so I dont like that setup :-)
>
> Brian
>
> On Wednesday 13 February 2002 20:15, you wrote:
> > Hi Brian,
> >
> > Yes, I can see that. In and out of MDI to reset DRO of jog encoder.
> > The encoders I have give just a little "feel". Your saying that 16
> > preset override values would work, why not just "scroll" through a list
> > of overrides, like the jog distance? Cheaper then BCD switches. I'd
> > think a 10 turn pot into an A/D converter would give good control also.
> > Now to figure out how to do the override in the motion code (mine).
> >
> > Alan KM6VV
Discussion Thread
Alan Marconett KM6VV
2002-02-11 14:48:32 UTC
RE: What is wanted in a controller, was Re: Correct or Max voltage for Bridgeport Nema 42? + more...
audiomaker2000
2002-02-11 18:08:57 UTC
What is wanted in a controller, was Re: Correct or Max voltage for Bridgeport Nema 42? + more...
Alan Marconett KM6VV
2002-02-11 20:19:10 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller, was Re: Correct or Max voltage for Bridgeport Nema 42? + more...
audiomaker2000
2002-02-11 23:08:38 UTC
What is wanted in a controller, was Re: Correct or Max voltage for Bridgeport Nema 42? + more...
ballendo
2002-02-12 04:53:13 UTC
What is wanted in a controller,
dave_ace_me
2002-02-12 05:15:36 UTC
Re: What is wanted in a controller,
Alan Marconett KM6VV
2002-02-12 11:14:15 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Drew Rogge
2002-02-12 11:21:56 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Jon Elson
2002-02-12 11:24:05 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-12 13:53:50 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-12 14:05:51 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Carol & Jerry Jankura
2002-02-12 14:16:14 UTC
RE: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-12 14:33:08 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller, was Re: Correct or Max voltage for Bridgeport Nema 42? + more...
Drew Rogge
2002-02-13 07:59:54 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-13 12:12:06 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Drew Rogge
2002-02-13 13:52:15 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-13 14:37:46 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Garry & Maxine Foster
2002-02-13 15:12:53 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Bill Vance
2002-02-13 15:21:55 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-13 16:17:30 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-13 16:20:48 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Brian Pitt
2002-02-13 18:59:07 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-13 20:12:17 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Brian Pitt
2002-02-13 21:27:37 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Alan Marconett KM6VV
2002-02-13 22:36:22 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Drew Rogge
2002-02-14 06:52:50 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,
Jon Elson
2002-02-14 09:46:27 UTC
Re: [CAD_CAM_EDM_DRO] What is wanted in a controller,