CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help

Posted by Rick Miller
on 2002-02-17 21:16:37 UTC
> Good evening! Whose drives are you using? You didn't say in your
> post. If they are ours, the help I can offer would be different if
> they are not.
>
Thanks for the reply Mariss! I'm using your Gecko 201 drives in this system.

> Second, check the return path for the step/direction outputs. If they
> are our drives I could give you specific suggestions. This means
> there has to be a "common" back either to the PC ground, or to PC
> +5VDC with our stuff.
>
I have most of the equipment put away for the night, so further testing will
have to wait 'til tomorrow. But, perhaps you've shown me my error right
here:
I have the step & direction lines connected as appropriate;
I have +5VDC connected to "Common";
I thought the 5V would ground to the "Power Ground", so I have no other
ground wires connected yet - which terminal should the 5V ground be
connected to?

> Don't feel bad, you are very close to having it all run. Your motors
> have holding torque; that's good. They just aren't getting step
> pulses for some reason. You are 95% of the way there.
>
> Mariss
Thanks for the encouragement & the help. You've answered quite a few
questions for me throughout this project, and it is GREATLY appreciated!!

Rick

Discussion Thread

Rick Miller 2002-02-17 19:27:45 UTC troubleshooting help aspaguy 2002-02-17 19:46:59 UTC Re: troubleshooting help Rick Miller 2002-02-17 20:37:26 UTC Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help mariss92705 2002-02-17 20:51:47 UTC Re: troubleshooting help Rick Miller 2002-02-17 21:16:37 UTC Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help Rick Miller 2002-02-17 21:28:03 UTC Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help mariss92705 2002-02-17 21:29:42 UTC Re: troubleshooting help mariss92705 2002-02-17 21:58:58 UTC Re: troubleshooting help Rick Miller 2002-02-17 22:11:36 UTC Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help ballendo 2002-02-18 02:35:07 UTC P-port 101 was Re: troubleshooting help Alan Marconett KM6VV 2002-02-18 12:49:56 UTC Re: [CAD_CAM_EDM_DRO] troubleshooting help Bob Bachman 2002-02-18 15:52:25 UTC Re: [CAD_CAM_EDM_DRO] troubleshooting help Carol & Jerry Jankura 2002-02-18 17:45:25 UTC RE: [CAD_CAM_EDM_DRO] troubleshooting help Carol & Jerry Jankura 2002-02-18 17:53:29 UTC RE: [CAD_CAM_EDM_DRO] troubleshooting help Alan Marconett KM6VV 2002-02-18 18:00:16 UTC Re: [CAD_CAM_EDM_DRO] troubleshooting help dkowalcz2000 2002-02-18 18:55:13 UTC Re: troubleshooting help Bob Bachman 2002-02-18 19:12:34 UTC RE: [CAD_CAM_EDM_DRO] troubleshooting help Jon Elson 2002-02-18 20:11:20 UTC Re: [CAD_CAM_EDM_DRO] troubleshooting help Rick Miller 2002-02-18 20:13:01 UTC Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help Rick Miller 2002-02-18 21:14:00 UTC Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help ballendo 2002-02-19 02:35:16 UTC more p-port 101 was Re: troubleshooting help ballendo 2002-02-19 04:01:49 UTC p-port alternative 8255PPI was Re: troubleshooting help ballendo 2002-02-19 04:39:13 UTC TTL 101 was Re: troubleshooting help Carol & Jerry Jankura 2002-02-19 05:44:14 UTC RE: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI was Re: troubleshooting help ballendo 2002-02-19 06:32:49 UTC p-port alternative 8255PPI Robert Bachman 2002-02-19 06:57:42 UTC Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help David Goodfellow 2002-02-19 08:37:36 UTC Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI was Re: troubleshooting help Carol & Jerry Jankura 2002-02-19 09:22:22 UTC RE: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI Alan Marconett KM6VV 2002-02-19 10:48:53 UTC Re: [CAD_CAM_EDM_DRO] troubleshooting help Bill Vance 2002-02-19 11:04:12 UTC Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help Bob Bachman 2002-02-19 11:24:21 UTC Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help Paul 2002-02-19 12:00:37 UTC Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI Alan Marconett KM6VV 2002-02-19 12:24:16 UTC Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help Alan Marconett KM6VV 2002-02-19 12:42:17 UTC Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI wanliker@a... 2002-02-19 13:36:28 UTC Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help Vajk Fekete 2002-02-19 14:24:21 UTC Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI Alan Marconett KM6VV 2002-02-19 16:06:28 UTC Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI Ian W. Wright 2002-02-19 16:35:00 UTC Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help