RE: [CAD_CAM_EDM_DRO] troubleshooting help
Posted by
Carol & Jerry Jankura
on 2002-02-18 17:53:29 UTC
Bob:
Standard logic means that a logic level zero is also represented by a
voltage level which is close to zero (normally under 0.8 volts) A logic
level 1 is represented by a voltage level which is close to the power supply
voltage (usually within a volt for 5 volt logic). Inverted logic means that
a logic level zero is represented by the voltage level which is close to the
power supply voltage and a logic level one is represented by a voltage level
close to zero.
-- Carol & Jerry Jankura
Strongsville, Ohio
So many toys, so little time....
|-----Original Message-----
|From: Bob Bachman [mailto:bobach@...]
|Sent: Monday, February 18, 2002 3:52 PM
|To: CAD_CAM_EDM_DRO@yahoogroups.com
|Subject: Re: [CAD_CAM_EDM_DRO] troubleshooting help
|
|
|Please explain ' inverted pins '.
|
|Does this mean the pins are normally at 0 volts and goes to -5 volts with
|input?
|Or are the pins at +5 volts normally and go to 0 volts with input?
|
|An uninverted pin would normally be at 0 volts and go to +5 volts with
|input, right?
|
|Thanks,
|
|Bob
|
|
|>Notice that several pins are inverted, per the CMD_MASK.
|
|
|[Non-text portions of this message have been removed]
|
|
|Addresses:
|FAQ: http://www.ktmarketing.com/faq.html
|FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
|
|Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
|Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
|Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
|List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
|Moderator: jmelson@... timg@... [Moderator]
|URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
|bill,
|List Manager
|
|
|
|Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
|
|
|
Standard logic means that a logic level zero is also represented by a
voltage level which is close to zero (normally under 0.8 volts) A logic
level 1 is represented by a voltage level which is close to the power supply
voltage (usually within a volt for 5 volt logic). Inverted logic means that
a logic level zero is represented by the voltage level which is close to the
power supply voltage and a logic level one is represented by a voltage level
close to zero.
-- Carol & Jerry Jankura
Strongsville, Ohio
So many toys, so little time....
|-----Original Message-----
|From: Bob Bachman [mailto:bobach@...]
|Sent: Monday, February 18, 2002 3:52 PM
|To: CAD_CAM_EDM_DRO@yahoogroups.com
|Subject: Re: [CAD_CAM_EDM_DRO] troubleshooting help
|
|
|Please explain ' inverted pins '.
|
|Does this mean the pins are normally at 0 volts and goes to -5 volts with
|input?
|Or are the pins at +5 volts normally and go to 0 volts with input?
|
|An uninverted pin would normally be at 0 volts and go to +5 volts with
|input, right?
|
|Thanks,
|
|Bob
|
|
|>Notice that several pins are inverted, per the CMD_MASK.
|
|
|[Non-text portions of this message have been removed]
|
|
|Addresses:
|FAQ: http://www.ktmarketing.com/faq.html
|FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
|
|Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
|Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
|Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
|List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
|Moderator: jmelson@... timg@... [Moderator]
|URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
|bill,
|List Manager
|
|
|
|Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
|
|
|
Discussion Thread
Rick Miller
2002-02-17 19:27:45 UTC
troubleshooting help
aspaguy
2002-02-17 19:46:59 UTC
Re: troubleshooting help
Rick Miller
2002-02-17 20:37:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help
mariss92705
2002-02-17 20:51:47 UTC
Re: troubleshooting help
Rick Miller
2002-02-17 21:16:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help
Rick Miller
2002-02-17 21:28:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help
mariss92705
2002-02-17 21:29:42 UTC
Re: troubleshooting help
mariss92705
2002-02-17 21:58:58 UTC
Re: troubleshooting help
Rick Miller
2002-02-17 22:11:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help
ballendo
2002-02-18 02:35:07 UTC
P-port 101 was Re: troubleshooting help
Alan Marconett KM6VV
2002-02-18 12:49:56 UTC
Re: [CAD_CAM_EDM_DRO] troubleshooting help
Bob Bachman
2002-02-18 15:52:25 UTC
Re: [CAD_CAM_EDM_DRO] troubleshooting help
Carol & Jerry Jankura
2002-02-18 17:45:25 UTC
RE: [CAD_CAM_EDM_DRO] troubleshooting help
Carol & Jerry Jankura
2002-02-18 17:53:29 UTC
RE: [CAD_CAM_EDM_DRO] troubleshooting help
Alan Marconett KM6VV
2002-02-18 18:00:16 UTC
Re: [CAD_CAM_EDM_DRO] troubleshooting help
dkowalcz2000
2002-02-18 18:55:13 UTC
Re: troubleshooting help
Bob Bachman
2002-02-18 19:12:34 UTC
RE: [CAD_CAM_EDM_DRO] troubleshooting help
Jon Elson
2002-02-18 20:11:20 UTC
Re: [CAD_CAM_EDM_DRO] troubleshooting help
Rick Miller
2002-02-18 20:13:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help
Rick Miller
2002-02-18 21:14:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: troubleshooting help
ballendo
2002-02-19 02:35:16 UTC
more p-port 101 was Re: troubleshooting help
ballendo
2002-02-19 04:01:49 UTC
p-port alternative 8255PPI was Re: troubleshooting help
ballendo
2002-02-19 04:39:13 UTC
TTL 101 was Re: troubleshooting help
Carol & Jerry Jankura
2002-02-19 05:44:14 UTC
RE: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI was Re: troubleshooting help
ballendo
2002-02-19 06:32:49 UTC
p-port alternative 8255PPI
Robert Bachman
2002-02-19 06:57:42 UTC
Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help
David Goodfellow
2002-02-19 08:37:36 UTC
Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI was Re: troubleshooting help
Carol & Jerry Jankura
2002-02-19 09:22:22 UTC
RE: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI
Alan Marconett KM6VV
2002-02-19 10:48:53 UTC
Re: [CAD_CAM_EDM_DRO] troubleshooting help
Bill Vance
2002-02-19 11:04:12 UTC
Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help
Bob Bachman
2002-02-19 11:24:21 UTC
Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help
Paul
2002-02-19 12:00:37 UTC
Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI
Alan Marconett KM6VV
2002-02-19 12:24:16 UTC
Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help
Alan Marconett KM6VV
2002-02-19 12:42:17 UTC
Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI
wanliker@a...
2002-02-19 13:36:28 UTC
Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help
Vajk Fekete
2002-02-19 14:24:21 UTC
Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI
Alan Marconett KM6VV
2002-02-19 16:06:28 UTC
Re: [CAD_CAM_EDM_DRO] p-port alternative 8255PPI
Ian W. Wright
2002-02-19 16:35:00 UTC
Re: [CAD_CAM_EDM_DRO] TTL 101 was Re: troubleshooting help