CAD CAM EDM DRO - Yahoo Group Archive

Re: looking a power supply for gecko

on 2002-02-23 07:25:32 UTC
where I can find a capacitator & bridge rectifier? I know nothing
about electronic and I do not know how to connect those stuff..
I am wondering if I better buy a good power suppy..

--- In CAD_CAM_EDM_DRO@y..., "Bob Campbell" <bob@c...> wrote:
> First download and read the white paper that is on the geckodrive
web site.
> It has all the information that you will need.
>
> For a four volt stepper motor you will need a supply of something
under 80
> volts. 80 volts is the maximum for the Gecko drives. I would stay
about 10%
> below that.
>
> Use an unregulated supply. For that all you would need is a
transformer,
> bridge rectifier and a filter capacitor. Use a fuse block and run
separate
> wires from the fuse block to each Gecko drive. Each drive should
have a
> separate 5 amp fuse.
>
> If you have problems, contact me off line and I will help you.
>
> Bob Campbell
> ----- Original Message -----
> From: "luisguillermo98" <luisguillermo98@y...>
> To: <CAD_CAM_EDM_DRO@y...>
> Sent: Friday, February 22, 2002 7:04 PM
> Subject: [CAD_CAM_EDM_DRO] looking a power supply for gecko
>
>
> > I will buy geckos driver soon but I do not what power supply will
> > work best for them?
> >
> > unregulated?
> > how much voltage?
> > how much amperes does it need to be?
> > where can I buy this power supply?
> >
> > my steppers are 4v and 2 amp....
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > Post messages: CAD_CAM_EDM_DRO@y...
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >

Discussion Thread

luisguillermo98 2002-02-22 19:04:22 UTC looking a power supply for gecko High Tech 2002-02-22 20:47:35 UTC RE: [CAD_CAM_EDM_DRO] looking a power supply for gecko Guy Sirois 2002-02-23 06:59:03 UTC RE: [CAD_CAM_EDM_DRO] looking a power supply for gecko Bob Campbell 2002-02-23 07:13:50 UTC Re: [CAD_CAM_EDM_DRO] looking a power supply for gecko luisguillermo98 2002-02-23 07:25:32 UTC Re: looking a power supply for gecko Carol & Jerry Jankura 2002-02-23 08:04:57 UTC RE: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko luisguillermo98 2002-02-26 20:05:51 UTC Re: looking a power supply for gecko Bob Campbell 2002-02-27 08:10:03 UTC RE: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko Peter 2002-02-27 08:38:55 UTC Re: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko luisguillermo98 2002-02-28 20:57:26 UTC Re: looking a power supply for gecko wanliker@a... 2002-02-28 21:26:33 UTC Re: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko JanRwl@A... 2002-03-01 19:26:23 UTC Re: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko