Re: looking a power supply for gecko

I really appreciate that Bob..

do you have a guide or something to start with?

--- In CAD_CAM_EDM_DRO@y..., "Bob Campbell" <bob@c...> wrote:
> I would suggest that you find a local Ham radio operator who could
give you
> some help. I can put together a document that would take you step
by step
> and wire by wire. I think that you will need someone to help you
with your
> first project.
>
> Bob Campbell
>
> -----Original Message-----
> From: luisguillermo98 [mailto:luisguillermo98@y...]
> Sent: Tuesday, February 26, 2002 10:06 PM
> To: CAD_CAM_EDM_DRO@y...
> Subject: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko
>
>
> Ok; it sound easy but where and how they are coonected? the manual
> you said does not said anything about it..
>
>
> --- In CAD_CAM_EDM_DRO@y..., "Bob Campbell" <bob@c...> wrote:
> > First download and read the white paper that is on the geckodrive
> web site.
> > It has all the information that you will need.
> >
> > For a four volt stepper motor you will need a supply of something
> under 80
> > volts. 80 volts is the maximum for the Gecko drives. I would stay
> about 10%
> > below that.
> >
> > Use an unregulated supply. For that all you would need is a
> transformer,
> > bridge rectifier and a filter capacitor. Use a fuse block and run
> separate
> > wires from the fuse block to each Gecko drive. Each drive should
> have a
> > separate 5 amp fuse.
> >
> > If you have problems, contact me off line and I will help you.
> >
> > Bob Campbell
> > ----- Original Message -----
> > From: "luisguillermo98" <luisguillermo98@y...>
> > To: <CAD_CAM_EDM_DRO@y...>
> > Sent: Friday, February 22, 2002 7:04 PM
> > Subject: [CAD_CAM_EDM_DRO] looking a power supply for gecko
> >
> >
> > > I will buy geckos driver soon but I do not what power supply
will
> > > work best for them?
> > >
> > > unregulated?
> > > how much voltage?
> > > how much amperes does it need to be?
> > > where can I buy this power supply?
> > >
> > > my steppers are 4v and 2 amp....
> > >
> > >
> > >
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > >
> > > Post messages: CAD_CAM_EDM_DRO@y...
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > Moderator: jmelson@a... timg@k... [Moderator]
> > > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > bill,
> > > List Manager
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> > >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> http://www.metalworking.com/news_servers.html
> http://www.metalworking.com/news_servers.html
>
> Post messages: CAD_CAM_EDM_DRO@y...
> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> Moderator: jmelson@a... timg@k... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/