RE: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko

I would suggest that you find a local Ham radio operator who could give you
some help. I can put together a document that would take you step by step
and wire by wire. I think that you will need someone to help you with your
first project.

Bob Campbell

-----Original Message-----
From: luisguillermo98 [mailto:luisguillermo98@...]
Sent: Tuesday, February 26, 2002 10:06 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: looking a power supply for gecko


Ok; it sound easy but where and how they are coonected? the manual
you said does not said anything about it..

--- In CAD_CAM_EDM_DRO@y..., "Bob Campbell" <bob@c...> wrote:
> First download and read the white paper that is on the geckodrive
web site.
> It has all the information that you will need.
>
> For a four volt stepper motor you will need a supply of something
under 80
> volts. 80 volts is the maximum for the Gecko drives. I would stay
about 10%
> below that.
>
> Use an unregulated supply. For that all you would need is a
transformer,
> bridge rectifier and a filter capacitor. Use a fuse block and run
separate
> wires from the fuse block to each Gecko drive. Each drive should
have a
> separate 5 amp fuse.
>
> If you have problems, contact me off line and I will help you.
>
> Bob Campbell
> ----- Original Message -----
> From: "luisguillermo98" <luisguillermo98@y...>
> To: <CAD_CAM_EDM_DRO@y...>
> Sent: Friday, February 22, 2002 7:04 PM
> Subject: [CAD_CAM_EDM_DRO] looking a power supply for gecko
>
>
> > I will buy geckos driver soon but I do not what power supply will
> > work best for them?
> >
> > unregulated?
> > how much voltage?
> > how much amperes does it need to be?
> > where can I buy this power supply?
> >
> > my steppers are 4v and 2 amp....
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > Post messages: CAD_CAM_EDM_DRO@y...
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

OFF Topic POSTS: General Machining
http://www.metalworking.com/news_servers.html
http://www.metalworking.com/news_servers.html

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/