CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe

Posted by Tim Goldstein
on 2002-02-28 21:04:10 UTC
I have had better luck with using R instead of IJ. Also with EMC you
want to set Vector to output to 6 decimal points. EMC requires that the
paths be correct to sub-nanometer range.

Tim
[Denver, CO]


> Next datapoint:
>
> I took everyone's advice, re-did the conversion to cast it in X and Y
> coordinates rather than X and Z, and the K-word errors went away.
>
> But now I'm getting this error whenever I hit the finishing pass:
>
> emctask.cc 229: rs724mgc_Error: Radius to end of arc differs
> from radius to start
>
> Here's the snippet of code that's creating this (I'll eliminate the
> roughing bit, which is a bunch of linear G01 / G00 moves):
>
> -----
>
> N600 G00 X0.574 Y-0.357
> N601 G01 X-0.095 Y-0.187
> N602 G00 X-0.095 Y0.000
> N603 G01 X-0.015 Y0.000
> N604 G03 X0.196 Y-0.049 I0.109 J0.016
> N605 G01 X0.503 Y-0.093
> N606 G03 X0.578 Y-0.185 I0.090 J0.062
> N607 G01 X0.578 Y-0.187
> N608 G01 X0.522 Y-0.299
> N609 G00 X-0.095 Y-0.299
> N610 G00 X-0.095 Y-0.187
> N611 G00 X-0.095 Y-1.762
>
> -----
>
> Fair warning, I haven't gone back to hit the books on this one. So if
> it's an obvious error, bear with me.
>
> Thanks,
>
> Tom
>
> (P.S. I got the scale on the part wrong, so it's not much to
> look at. As
> soon as I get everything working right, I'll take pictures and post
> stuff.)

Discussion Thread

rainnea 2002-01-18 15:09:32 UTC 5-axis Taig Mill Scott A. Stephens 2002-01-19 21:10:14 UTC Re: [CAD_CAM_EDM_DRO] 5-axis Taig Mill rainnea 2002-01-20 05:44:55 UTC Re: 5-axis Taig Mill Scott A. Stephens 2002-01-20 15:04:02 UTC Re: [CAD_CAM_EDM_DRO] Re: 5-axis Taig Mill Tony Jeffree 2002-01-21 07:28:55 UTC Re: 5-axis Taig Mill Michael Milligan 2002-01-21 08:29:56 UTC RE: [CAD_CAM_EDM_DRO] Re: 5-axis Taig Mill Andrew Werby 2002-01-21 11:27:40 UTC Re: 5-axis Taig Mill rainnea 2002-01-21 14:11:25 UTC Re: 5-axis Taig Mill Alan Marconett KM6VV 2002-01-21 15:47:33 UTC Re: 5-axis Taig Mill rainnea 2002-01-21 18:12:33 UTC Re: 5-axis Taig Mill Alan Marconett KM6VV 2002-01-21 18:43:25 UTC Re: 5-axis Taig Mill rainnea 2002-01-22 00:50:10 UTC Re: 5-axis Taig Mill ballendo 2002-01-22 07:32:24 UTC Re: 5-axis Taig Mill Alan Marconett KM6VV 2002-01-22 10:31:52 UTC Re: 5-axis Taig Mill Tom Benedict 2002-02-28 07:17:14 UTC VectorCam Demo and EMC - Lathe Tom Benedict 2002-02-28 08:15:26 UTC Re: VectorCam Demo and EMC - Lathe Matt Shaver 2002-02-28 09:14:56 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Scot Rogers 2002-02-28 09:25:33 UTC RE: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Jon Elson 2002-02-28 11:02:18 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Chris Clough 2002-02-28 11:06:17 UTC CAM Software Tim Goldstein 2002-02-28 11:35:34 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Tom Benedict 2002-02-28 11:58:15 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Tom Benedict 2002-02-28 12:03:35 UTC Re: [CAD_CAM_EDM_DRO] CAM Software Chris Clough 2002-02-28 12:16:25 UTC RE: [CAD_CAM_EDM_DRO] CAM Software follicely_challenged 2002-02-28 12:51:56 UTC Re: CAM Software Chris Clough 2002-02-28 12:53:52 UTC RE: [CAD_CAM_EDM_DRO] Re: CAM Software Alan Marconett KM6VV 2002-02-28 13:27:10 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Alan Marconett KM6VV 2002-02-28 13:42:46 UTC Re: VectorCam Demo and EMC - Lathe vrsculptor 2002-02-28 13:43:36 UTC Re: CAM Software Peter 2002-02-28 13:59:52 UTC Re: [CAD_CAM_EDM_DRO] Re: CAM Software Bob Campbell 2002-02-28 14:05:49 UTC RE: [CAD_CAM_EDM_DRO] CAM Software Tom Benedict 2002-02-28 14:09:08 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Alan Marconett KM6VV 2002-02-28 14:19:58 UTC Re: [CAD_CAM_EDM_DRO] CAM Software Hugh Currin 2002-02-28 14:29:40 UTC Re: VectorCam Demo and EMC - Lathe Alan Marconett KM6VV 2002-02-28 14:39:16 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe stevenson_engineers 2002-02-28 14:52:51 UTC Re: CAM Software Alan Marconett KM6VV 2002-02-28 15:11:23 UTC Re: VectorCam Demo and EMC - Lathe Tom Benedict 2002-02-28 18:06:04 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Alan Marconett KM6VV 2002-02-28 18:21:07 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe vrsculptor 2002-02-28 19:17:25 UTC Re: CAM Software docholliday01201 2002-02-28 19:33:11 UTC Re: CAM Software imserv1 2002-02-28 21:00:51 UTC Re: VectorCam Demo and EMC - Lathe Tim Goldstein 2002-02-28 21:04:10 UTC RE: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Jon Elson 2002-02-28 23:08:41 UTC Re: [CAD_CAM_EDM_DRO] VectorCam Demo and EMC - Lathe Tony Jeffree 2002-02-28 23:23:59 UTC Re: VectorCam Demo and EMC - Lathe ptengin@a... 2002-03-01 01:10:58 UTC [CAD_CAM_EDM_DRO] CAM Software Tom Benedict 2002-03-01 07:19:09 UTC Re: [CAD_CAM_EDM_DRO] Re: VectorCam Demo and EMC - Lathe Tom Benedict 2002-03-03 19:33:19 UTC Re: [CAD_CAM_EDM_DRO] Re: VectorCam Demo and EMC - Lathe