Re: [CAD_CAM_EDM_DRO] Power supply question.....
Posted by
RC
on 2002-04-24 13:52:09 UTC
Ok...... try to solve the transformer question with this final information:
(Secondary face of transformer)
I~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~I
I 0--fuse-0 < 8.0v >0 I
I I
I I
I I
I I = no. of wires to each terminal I
I I
I II IIII II I
I O O O I
I~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~I
I < 3.1v > I< 28.5v >I
I< 31.5v >I
Well, I think you got the picture now..... the bottom three terminals have
the heavy wire, while the top three have lighter gauge....not sure what the
fuse is for?
RC
(Secondary face of transformer)
I~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~I
I 0--fuse-0 < 8.0v >0 I
I I
I I
I I
I I = no. of wires to each terminal I
I I
I II IIII II I
I O O O I
I~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~I
I < 3.1v > I< 28.5v >I
I< 31.5v >I
Well, I think you got the picture now..... the bottom three terminals have
the heavy wire, while the top three have lighter gauge....not sure what the
fuse is for?
RC
----- Original Message -----
From: <JanRwl@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, April 23, 2002 8:37 PM
Subject: Re: [CAD_CAM_EDM_DRO] Power supply question.....
> In a message dated 23-Apr-02 04:58:42 Central Daylight Time,
asdf@...
> writes:
>
>
> > My question is, can one use any
> > combination of connection without being a problem?
>
>
> Wow, a "loaded" question! It depends on the combinations, of course!
>
> If I read your description of your transformer's secondary correctly, it
is
> NOT a "Center Tap", but a tap near one end of the winding! If the voltage
> between the ENDS of a winding are 32 VAC, then the voltage between the
"CT"
> and EITHER end will be 16 VAC!
>
> Can you see the "magnet wire" in the transformer that connects to these
> terminals, or are the connections to the "outside world" made to insulated
> "hook-up wire", so the joints are hidden? If you can actually see the
ends
> of the magnet-wire soldered to terminals to which you connect your
circuitry
> or voltmeter, is the wire-size (diameter) the same on the "end
connections",
> and there are TWO wires to the "CT"? Reason I am asking this is that I
> imagine you might have different windings or some such. A "CT" is NOT a C
> enter-Tap if the voltage is not "same" to EITHER "end terminal".
>
> You can use a "rectifier bridge" (or four suitably-large silicon diodes)
and
> ONLY the "end terminals" to give you "full-wave DC". Or, you can connect
a
> (real, actual) "CT" to ground, and then use a single silicon-diode in
series
> with EACH end-terminal, their cathodes connected, providing +, also
full-wave
> DC. There are disadvantages and ADvantages to each method. You kinda
hafta
> "know a bit of whatcha DOIN' with this" to go on!
>
> Lotsa luck! Jan Rowland, Old Troll
>
>
> [Non-text portions of this message have been removed]
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
RC
2002-04-22 03:04:20 UTC
Power supply question.....
steveggca
2002-04-22 04:12:47 UTC
Re: Power supply question.....
Brian
2002-04-22 05:39:05 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
scott wilson
2002-04-22 06:14:24 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
JanRwl@A...
2002-04-22 19:15:52 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
RC
2002-04-23 02:57:40 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
dave_ace_me
2002-04-23 07:23:13 UTC
Cap voltage rating (was Re: Power supply question.....
scott wilson
2002-04-23 07:53:58 UTC
Re: [CAD_CAM_EDM_DRO] Cap voltage rating (was Re: Power supply question.....
scott wilson
2002-04-23 08:00:38 UTC
Re: [CAD_CAM_EDM_DRO] Cap voltage rating (was Re: Power supply question.....
Jon Elson
2002-04-23 10:42:01 UTC
Re: [CAD_CAM_EDM_DRO] Cap voltage rating (was Re: Power supply question.....
beer@s...
2002-04-23 11:33:35 UTC
Re: Re: Power supply question.....
scott wilson
2002-04-23 12:40:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....
Tim Goldstein
2002-04-23 13:02:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....
Raymond Heckert
2002-04-23 13:12:20 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
studleylee
2002-04-23 13:20:31 UTC
Re: Power supply question.....A Good Cap info link
scott wilson
2002-04-23 13:38:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Power supply question.....A Good Cap info link
scott wilson
2002-04-23 13:54:34 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
JanRwl@A...
2002-04-23 20:37:27 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
Jon Elson
2002-04-23 23:01:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....
Jon Elson
2002-04-23 23:07:26 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
batwings@i...
2002-04-24 05:12:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....
beer@s...
2002-04-24 13:26:32 UTC
Re: Re: Re: Power supply question.....
dave_ace_me
2002-04-24 13:49:33 UTC
Re: Power supply question.....
RC
2002-04-24 13:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
Raymond Heckert
2002-04-24 20:47:54 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
Raymond Heckert
2002-04-24 20:48:01 UTC
Re: [CAD_CAM_EDM_DRO] Power supply question.....
ballendo
2002-04-26 01:05:19 UTC
Technical help was Cap voltage rating (was Re: Power supply question.....
ballendo
2002-04-26 01:12:56 UTC
conflicting answers? was Re: Power supply question.....A Good Cap info link
Jon Elson
2002-05-02 22:14:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Power supply question.....
scott wilson
2002-05-03 04:38:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Power supply question.....
Jon Elson
2002-05-03 10:15:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Power supply question.....
scott wilson
2002-05-03 10:23:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Power supply question.....
JanRwl@A...
2002-05-03 20:36:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Power supply question.....
Jon Elson
2002-05-03 23:01:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Power supply question.....
mariss92705
2002-05-04 00:28:35 UTC
Re: Re: Power supply question.....
JanRwl@A...
2002-05-04 09:03:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....
Tim Goldstein
2002-05-04 09:51:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....
Jon Elson
2002-05-04 22:24:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Power supply question.....