Re: Question for Mariss
Posted by
mariss92705
on 2002-05-18 09:14:15 UTC
Not a good idea. The voltage swing is 12V on that pin and connecting
the port ground to term. 12 eliminates the benefit of opto-isolation.
Use an opto-isolator or a 5VDC reed relay instead.
Mariss
the port ground to term. 12 eliminates the benefit of opto-isolation.
Use an opto-isolator or a 5VDC reed relay instead.
Mariss
--- In CAD_CAM_EDM_DRO@y..., "rsgoldner" <rgoldner@i...> wrote:
> Can I connect a parallel port output pin directly to pin 7
(disable)
> on a Gecko 201 without smoking it? Would the PPort ground be
> connected to pin 12?
Discussion Thread
rsgoldner
2002-02-13 06:36:39 UTC
Question for Mariss
a_w_abate
2002-02-13 09:20:25 UTC
Re: Question for Mariss
rsgoldner
2002-02-13 09:51:57 UTC
Re: Question for Mariss
dave_ace_me
2002-02-13 10:06:29 UTC
Re: Question for Mariss
mariss92705
2002-02-13 10:36:35 UTC
Re: Question for Mariss
rsgoldner
2002-02-13 10:58:07 UTC
Re: Question for Mariss
mariss92705
2002-02-13 12:12:16 UTC
Re: Question for Mariss
NCS
2002-02-13 12:44:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss
rsgoldner
2002-02-13 13:52:17 UTC
Re: Question for Mariss
mariss92705
2002-02-13 15:00:10 UTC
Re: Question for Mariss
rsgoldner
2002-02-13 15:42:47 UTC
Re: Question for Mariss
dave_ace_me
2002-02-13 17:45:37 UTC
Re: Question for Mariss
rsgoldner
2002-05-18 09:04:09 UTC
Question for Mariss
mariss92705
2002-05-18 09:14:15 UTC
Re: Question for Mariss
Scott Hendershot
2002-05-18 21:27:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss
JanRwl@A...
2002-05-18 22:47:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss
Scott Hendershot
2002-05-19 08:38:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss
rsgoldner
2002-05-19 09:23:11 UTC
Re: Question for Mariss
Weyland
2003-09-14 01:15:24 UTC
Question for Mariss
Jon Elson
2003-09-14 22:14:09 UTC
Re: [CAD_CAM_EDM_DRO] Question for Mariss
Mariss Freimanis
2003-09-14 22:52:23 UTC
Re: Question for Mariss
Weyland
2003-09-15 02:08:07 UTC
Re: [CAD_CAM_EDM_DRO] Question for Mariss
Weyland
2003-09-15 02:09:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss
turbulatordude
2003-09-15 08:35:52 UTC
Re: Question for Mariss
Weyland
2003-09-15 10:26:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss