CAD CAM EDM DRO - Yahoo Group Archive

Question for Mariss

Posted by Weyland
on 2003-09-14 01:15:24 UTC
Mariss,

During a web search on the motors I have and am
trying to use, I found some posts from a date later
than when I bought my motors, right here in this group.

Here's the question -
How do I know what revision my Gecko G210s are?
Mine are marked with a "90IFX" on the covers.

The reason I ask is that I just found
out that mine may not work for my motors.

The post and motors described are found here -

http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/message/40840?source=1

Basically, they are Nema 42, Sigma 20-4247TD200-F1.3 motors.

200 step
540 oz-in @ 50 sps
635 oz-in holding
22.6 oz-in detent torque
5.0 Amp phase current
1.29 ohms phase resistance
2.2 mH phase inductance
17.4 oz-in^2 rotor inertia
10 lbs. weight, 30 watts dissipation, 8-wire

Also, and this is for anyone, but I think you'll certainly be able
to advise me, am I better off running these in series or parallel?
These are mounted on a RongFu RF20 benchtop mill.

Thanks for your time,

Weyland

Discussion Thread

rsgoldner 2002-02-13 06:36:39 UTC Question for Mariss a_w_abate 2002-02-13 09:20:25 UTC Re: Question for Mariss rsgoldner 2002-02-13 09:51:57 UTC Re: Question for Mariss dave_ace_me 2002-02-13 10:06:29 UTC Re: Question for Mariss mariss92705 2002-02-13 10:36:35 UTC Re: Question for Mariss rsgoldner 2002-02-13 10:58:07 UTC Re: Question for Mariss mariss92705 2002-02-13 12:12:16 UTC Re: Question for Mariss NCS 2002-02-13 12:44:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss rsgoldner 2002-02-13 13:52:17 UTC Re: Question for Mariss mariss92705 2002-02-13 15:00:10 UTC Re: Question for Mariss rsgoldner 2002-02-13 15:42:47 UTC Re: Question for Mariss dave_ace_me 2002-02-13 17:45:37 UTC Re: Question for Mariss rsgoldner 2002-05-18 09:04:09 UTC Question for Mariss mariss92705 2002-05-18 09:14:15 UTC Re: Question for Mariss Scott Hendershot 2002-05-18 21:27:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss JanRwl@A... 2002-05-18 22:47:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss Scott Hendershot 2002-05-19 08:38:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss rsgoldner 2002-05-19 09:23:11 UTC Re: Question for Mariss Weyland 2003-09-14 01:15:24 UTC Question for Mariss Jon Elson 2003-09-14 22:14:09 UTC Re: [CAD_CAM_EDM_DRO] Question for Mariss Mariss Freimanis 2003-09-14 22:52:23 UTC Re: Question for Mariss Weyland 2003-09-15 02:08:07 UTC Re: [CAD_CAM_EDM_DRO] Question for Mariss Weyland 2003-09-15 02:09:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss turbulatordude 2003-09-15 08:35:52 UTC Re: Question for Mariss Weyland 2003-09-15 10:26:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Question for Mariss