Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
Posted by
Steve Blackmore
on 2002-05-31 02:06:11 UTC
On Thu, 30 May 2002 22:13:40 -0000, you wrote:
port pins or TTL signal or whatever, Pin 8 is ground, Pin 9 is Input
Power , Pins 10-16 are the outputs.
eg - +12V to pin 9, connect Pin1 to parallel port, say pin 11, apply a
signal to // port pin 11 and you get +12V at ULN Pin16. Remove the
signal and Pin16 switches off. Great for driving relays for spindle,
coolant etc.
Steve Blackmore
--
Pilot Consultancy Limited ***** Computer Consultants
Telephone 01744 752256 Mobile 07831 768478
Email: steve@... WWW: http://www.pilotltd.net
>Sounds like this would be pushing my limited electronics knowledge.Couldn't be easier with a ULN2003 - pins 1-7 connect to a parallel
>
port pins or TTL signal or whatever, Pin 8 is ground, Pin 9 is Input
Power , Pins 10-16 are the outputs.
eg - +12V to pin 9, connect Pin1 to parallel port, say pin 11, apply a
signal to // port pin 11 and you get +12V at ULN Pin16. Remove the
signal and Pin16 switches off. Great for driving relays for spindle,
coolant etc.
Steve Blackmore
--
Pilot Consultancy Limited ***** Computer Consultants
Telephone 01744 752256 Mobile 07831 768478
Email: steve@... WWW: http://www.pilotltd.net
Discussion Thread
rainnea
2002-05-30 05:32:14 UTC
Opto / relay recommendation
Larry Van Duyn
2002-05-30 05:48:35 UTC
Re: [CAD_CAM_EDM_DRO] Opto / relay recommendation
Alan Marconett KM6VV
2002-05-30 12:54:33 UTC
Re: [CAD_CAM_EDM_DRO] Opto / relay recommendation
rainnea
2002-05-30 15:10:11 UTC
Re: Opto / relay recommendation
JanRwl@A...
2002-05-30 15:10:30 UTC
Re: [CAD_CAM_EDM_DRO] Opto / relay recommendation
rainnea
2002-05-30 15:13:43 UTC
Re: Opto / relay recommendation
Larry Van Duyn
2002-05-30 15:22:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
Nic van der Walt
2002-05-30 15:29:41 UTC
RE: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
rainnea
2002-05-30 15:31:26 UTC
Re: Opto / relay recommendation
rainnea
2002-05-30 16:02:31 UTC
Re: Opto / relay recommendation
JanRwl@A...
2002-05-30 17:02:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
JanRwl@A...
2002-05-30 17:12:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
Eric Keller
2002-05-30 17:14:33 UTC
Opto / relay recommendation
Steve Blackmore
2002-05-31 02:06:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
Mark Taft
2002-05-31 02:52:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
JanRwl@A...
2002-05-31 14:46:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
rainnea
2002-05-31 15:25:40 UTC
Re: Opto / relay recommendation
Steve Blackmore
2002-05-31 16:45:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
JanRwl@A...
2002-05-31 17:06:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation
rainnea
2002-06-01 03:54:59 UTC
Re: Opto / relay recommendation
rainnea
2002-06-01 04:04:39 UTC
Re: Opto / relay recommendation
JanRwl@A...
2002-06-01 11:32:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Opto / relay recommendation