CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges

Posted by Doug Harrison
on 2002-07-06 21:43:53 UTC
>> The variabiltly of the rail would
> > be the width of the hole in the placards.
> > Any thoughts or suggestions?

I just tried a #70 (that's small) carburetor jet for the hole. It gets the
spot down to about .010" as long as the hole is close to the spot. With the
hole two feet from the wall the spot grows to about .050" and gets worse as
the pinhole to spot separation increases. I think its that diffusion thing.

Doug

Discussion Thread

Les Watts 2002-07-02 12:07:04 UTC Creating long straight edges Carlos Guillermo 2002-07-02 12:34:51 UTC RE: [CAD_CAM_EDM_DRO] Creating long straight edges John Craddock 2002-07-02 21:09:59 UTC RE: [CAD_CAM_EDM_DRO] Creating long straight edges Les Watts 2002-07-03 05:20:47 UTC Re: [CAD_CAM_EDM_DRO] Creating long straight edges Country Bubba 2002-07-03 15:33:10 UTC Re: [CAD_CAM_EDM_DRO] Creating long straight edges Doug Harrison 2002-07-06 21:26:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges Doug Harrison 2002-07-06 21:43:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges cnc_4_me 2002-07-06 22:42:45 UTC Re: Creating long straight edges Ian W. Wright 2002-07-07 00:48:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges Les Watts 2002-07-07 04:56:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges turbulatordude 2002-07-07 05:48:12 UTC Re: Creating long straight edges Les Watts 2002-07-07 07:21:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges Jon Elson 2002-07-07 09:44:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges Jon Elson 2002-07-07 09:48:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges drking777 2002-07-08 07:15:26 UTC Re: Creating long straight edges Les Watts 2002-07-08 08:48:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Creating long straight edges drking777 2002-07-10 20:53:50 UTC Flat surface creation revisted Jon Elson 2002-07-10 22:39:19 UTC Re: [CAD_CAM_EDM_DRO] Flat surface creation revisted turbulatordude 2002-07-11 06:21:48 UTC Re: Flat surface creation revisted Doug Harrison 2002-07-11 13:22:54 UTC Re: [CAD_CAM_EDM_DRO] Flat surface creation revisted drking777 2002-07-11 14:07:27 UTC Re: Flat surface creation revisted drking777 2002-07-11 14:21:53 UTC Re: Flat surface creation revisted Doug Harrison 2002-07-11 16:19:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat surface creation revisted turbulatordude 2002-07-11 17:41:09 UTC Re: Flat surface creation revisted (concrete)