Re: acceleration profille (gained steps?)
Posted by
keongsan
on 2002-07-27 05:04:39 UTC
--- In CAD_CAM_EDM_DRO@y..., "Dan Mauch" <dmauch@s...> wrote:
Thanks. You are always dependable. Reset the parameters to
max sps: 1500sps ( ~9ipm)
start v: 500
acceler: 1000spss
Running the engraving program with xy feedrate 5ipm, everything OK.
However, when I tried to run the same program with xy feedrate at 9ipm
the result was distorted. looks like at a "small part" of the
begginning of the program, x was "amplified" like when the intended
result was a V, it has ended up with a fat \/ extended in the x
direction - the opposite of lost steps (is there such a fault a
gained steps?
Running the program at 6ipm was OK.
Thanks
keongsan
> You have the max steps per seconds is way too high. Start at 1500not
> 15000 then adjust upward till it starts losing steps then back offabout
> 10%. Also your acceleration is way too high. Start at 1000 sps.Also the
> start velocity is high start at 500 and increase.Hi Dan,
> Dan
Thanks. You are always dependable. Reset the parameters to
max sps: 1500sps ( ~9ipm)
start v: 500
acceler: 1000spss
Running the engraving program with xy feedrate 5ipm, everything OK.
However, when I tried to run the same program with xy feedrate at 9ipm
the result was distorted. looks like at a "small part" of the
begginning of the program, x was "amplified" like when the intended
result was a V, it has ended up with a fat \/ extended in the x
direction - the opposite of lost steps (is there such a fault a
gained steps?
Running the program at 6ipm was OK.
Thanks
keongsan
> -----Original Message-----box,
> From: keongsan [mailto:keongsan@y...]
> Sent: Friday, July 26, 2002 2:02 AM
> To: CAD_CAM_EDM_DRO@y...
> Subject: [CAD_CAM_EDM_DRO] acceleration profille
>
> Hi,
>
> Having some problem with the z-axis in the cnc'ed sherline with
> Sherline stepper 1/2 winding, Camtronics 2A driver, desknc black
> with the parameters set up as follows500
>
>
> Acceleration=5000
> maxsps=15000
> start_vel=5000
> steps/mm=400
>
> The z-axis seem to be loosing steps very badly. The z-axis seem to
> jerk, and hardly move. I set the accel. to 500 and start vel. to
> and problem persist. I think it may be the parameters may not bereach it
> suitable for this configuration.
>
> Can someone suggest a suitable parameter for this set-up or let us
> know about the parameters which is working with your system.
>
> Thanks in advance
>
> keongsan
>
>
>
>
>
>
>
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> if you have trouble.there,
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
> sister site to the CCED group, as many of the same members are
> for OT subjects, that are not allowed on the CCED list.THEM.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>
> Post messages: CAD_CAM_EDM_DRO@y...
> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> Moderator: jmelson@a... timg@k... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
Discussion Thread
keongsan
2002-07-26 02:01:35 UTC
acceleration profille
Dan Mauch
2002-07-26 11:19:31 UTC
RE: [CAD_CAM_EDM_DRO] acceleration profille
Dave Hylands
2002-07-26 11:31:42 UTC
RE: [CAD_CAM_EDM_DRO] acceleration profille
cadcambee
2002-07-26 17:21:48 UTC
Re: acceleration profille
keongsan
2002-07-27 05:04:39 UTC
Re: acceleration profille (gained steps?)
jmkasunich
2002-07-27 12:26:06 UTC
Re: acceleration profille
Graham Hollis
2002-07-27 15:05:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: acceleration profille
Michael Holm
2002-07-27 16:49:00 UTC
Re: [CAD_CAM_EDM_DRO] acceleration profille
jmkasunich
2002-07-27 17:02:37 UTC
Re: acceleration profille
Alan Marconett KM6VV
2002-07-27 17:30:05 UTC
Re: [CAD_CAM_EDM_DRO] acceleration profille
cadcambee
2002-07-27 18:08:52 UTC
Re: acceleration profille
mariss92705
2002-07-27 19:52:51 UTC
Re: acceleration profille
Alan Marconett KM6VV
2002-07-28 11:26:47 UTC
Re: acceleration profille
keongsan
2002-07-28 16:57:15 UTC
Re: acceleration profille (gained steps?)
keongsan
2002-07-28 17:01:16 UTC
Re: acceleration profille (gained steps?)
Steve Blackmore
2002-07-28 17:34:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: acceleration profille
Dave Hylands
2002-07-28 18:00:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: acceleration profille (gained steps?)
mariss92705
2002-07-28 18:20:29 UTC
Re: acceleration profille (gained steps?)
Alan Marconett KM6VV
2002-07-28 19:57:30 UTC
Re: acceleration profille
MIKEC@W...
2002-07-28 21:41:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: acceleration profille
MIKEC@W...
2002-07-28 21:44:17 UTC
Re: [CAD_CAM_EDM_DRO] acceleration profille
chapmani
2002-07-29 02:11:59 UTC
Re: acceleration profille
eforum3001
2002-07-29 04:04:01 UTC
Re: acceleration profille (gained steps?)