CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it?

Posted by Jon Anderson
on 2002-08-17 08:41:25 UTC
On 8/15/02 7:59 AM, "JanRwl@..." <JanRwl@...> wrote:
>
> Ken: Perhaps very obvious, but make certain the distance between the
> magnet's and the reed switch's "long axes" will not vary, as this will change
> the "point of firing" considerably. A reed-switch can not be expected to be
> "repeatable" in an installation like this closer than a few tens of
> thousandths,

Years ago I tested some little no-name reed switches I had, using the
small approx 3/16 rare earth magnets Radio Shack sells, they would trip
consistently within about .0002. This was repeatable within a distance
range of at least .100 variation between magnet and switch. At some
point it does change of course, but small rare earth magnets will give
all the repeatability anyone could want. They'll also do a great job of
making ferrous fur balls too...<G>

Jon

Discussion Thread

mszollar 2002-08-14 22:26:35 UTC Reed switch for limits - anyone done it? Peter Homann 2002-08-14 22:46:54 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Ian W. Wright 2002-08-15 00:48:47 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? JJ 2002-08-15 05:45:03 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Carol & Jerry Jankura 2002-08-15 06:09:43 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? JanRwl@A... 2002-08-15 07:59:48 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-15 10:27:42 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Matt Shaver 2002-08-15 18:26:37 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-15 18:36:50 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Carol & Jerry Jankura 2002-08-15 20:54:59 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Matt Shaver 2002-08-15 21:20:18 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-16 09:44:39 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Jon Elson 2002-08-16 10:18:18 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-16 12:51:13 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Dave Engvall 2002-08-17 08:16:15 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Jon Anderson 2002-08-17 08:41:25 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? mszollar 2002-08-17 12:44:52 UTC Re: Reed switch for limits - anyone done it? Bill Vance 2002-08-17 15:44:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Reed switch for limits - anyone done it? turbulatordude 2002-08-17 20:10:00 UTC Re: Reed switch for limits - anyone done it?